Dimplex BF9000 Manuel d'entretien - Page 11

Parcourez en ligne ou téléchargez le pdf Manuel d'entretien pour {nom_de_la_catégorie} Dimplex BF9000. Dimplex BF9000 17 pages. Dimplex
Également pour Dimplex BF9000 : Manuel du propriétaire (19 pages), Manuel du propriétaire (20 pages), Manuel de dépannage (2 pages), Manuel du propriétaire (19 pages), Manuel d'entretien (18 pages)

Imprimer la page

grees, rest it inside the cavity in the top to provide you

with some support and leverage while following Step 4.

CAUTION: Support the back underside of the firebox

with a small piece of wood as the feet do not go the entire

depth of the unit and it can easily tip backwards.

3. Remove the 2 mounting brackets that attach to the

heater assembly to the top panel. Ensure that the heat-

er assembly is supported when removing the brackets.

4. Locate the High Temperature Cutout found on the outer

casing of the heater assembly at the elements.

5. Follow the wires to the terminal block and disconnect

the 2 wires at the terminal block.

6. Using a small diameter, Philips screwdriver, remove the

old cutout and replace it with the new one following the

orientation of the original wires. (See Assembly Part

Pictures)

7. Re-assemble in reverse order as described above.

3-POSITION OR HEATER SWITCH

REPLACEMENT

Tools Required: Philips head screwdriver

Needle nose pliers

CAUTION: Follow "Preparation for Service" instructions

before proceeding.

1. Remove 9 screws that secure the top panel to the side

panels of the firebox using a Philips head screwdriver,

(2) on the left side; (2) on the right side; (3) on the

backside; (2) on the top.

2. Lift the top panel up off the firebox, turn it 45 degrees

and rest it inside the upper cavity against the back

panel.

CAUTION: Support the back underside of the firebox

with a small piece of wood as the feet do not go the entire

depth of the unit and it can easily tip backwards.

3. The switch housing panel spans across the front of the

fireplace, near the top. Remove the 6 screws from the

side panels that hold this front panel in place, (3) on the

left and (3) on the right side.

4. Lift the switch-housing panel up and flip it 180 degrees

towards you to expose the wires connected to the

backside of the switch.

5. Taking note of the original location of each wire con-

nected to the switch that needs replacing, (either the

3-Position or the Heater Switch) remove the wires.

NOTE: Using a flat head screwdriver gently pry be-

tween the end of the connector and the switch to release

the wires.

6. Noting the orientation of the switches - the markings

on the face, depress the tabs that secure the switch to

the housing from behind the panel and push the switch

out to the front. Using needle nosed pliers will give you

a better grip and fit to depress both these tabs at the

same time.

7. Push the new switch in place, ensuring that both tabs

are engaged.

8. Re-assemble in reverse order as described above.

THERMOSTAT REPLACEMENT

Tools Required: Philips head screwdriver

CAUTION: Follow "Preparation for Service" instructions

before proceeding.

1. Remove 9 screws that secure the top panel to the side

panels of the firebox using a Philips head screwdriver,

(2) on the left side; (2) on the right side; (3) on the

backside; (2) on the top.

2. Lift the top panel up off the firebox, turn it 45 degrees

and rest it inside the upper cavity against the back

panel.

CAUTION: Support the back underside of the firebox

with a small piece of wood as the feet do not go the entire

depth of the unit and it can easily tip backwards.

3. On the front face of the switch housing, remove the 2

screws that hold the thermostat to the panel.

4. The switch housing panel spans across the entire top

on the front of the fireplace. Remove the 6 screws from

the side panels that hold this front panel in place, (3) on

the left and (3) on the right side.

5. Lift the switch-housing panel up and flip it 180 degrees

towards you to expose the wires connected to the

backside of the thermostat.

6. Remove the dial off the control shaft by pulling forward

away from the thermostat.

NOTE: Note that the dial will only go back on the shaft

one way when replacing.

7. Remove thermostat from the mounting bracket by re-

moving the 2 Philips screws located on the bracket.

8. Taking note of the original location of each wire con-

nected to the thermostat remove the wires and place

onto the new thermostat.

NOTE: Using a flat head screwdriver gently pry

between the end of the connector and the thermostat to

release the wires.

9. Re-assemble in reverse order as described above.

REMOTE CONTROL RECEIVER

REPLACEMENT

Tools Required: Philips head screwdriver

Needle nose pliers

Small cutter or snips

CAUTION: Follow "Preparation for Service" instructions

before proceeding.

1. Remove 9 screws that secure the top panel to the side

panels of the firebox using a Philips head screwdriver,

(2) on the left side; (2) on the right side; (3) on the

backside; (2) on the top.

2. Lift the top panel up off the firebox, turn it 45 degrees

and rest it inside the upper cavity against the back