Philips AZ-2040 Manuel de l'utilisateur - Page 10

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Philips AZ-2040. Philips AZ-2040 15 pages. Cd soundmachine
Également pour Philips AZ-2040 : Manuel de l'utilisateur (9 pages), Manuel de l'utilisateur (12 pages), Manuel (8 pages), Manuel d'entretien (34 pages), Manuel (10 pages), (suédois) Snabbmanual (8 pages)

Imprimer la page

BASIC FUNCTIONS

Batteries (not included)

• Insert 6 batteries, type R-20, UM-1 or D-cells,

(preferably alkaline) with the correct polarity.

Remote control (for AZ2045 only /See A)

• Insert 2 batteries, type AAA, R03 or UM4

(preferably alkaline).

Incorrect use of batteries can cause electrolyte

leakage and will corrode the compartment or cause

the batteries to burst.

• Do not mix battery types: e.g. alkaline with carbon

zinc. Only use batteries of the same type for the

set.

• When inserting new batteries, do not try to mix old

batteries with the new ones.

• Batteries contain chemical substances, so

they should be disposed of properly.

Using AC Power

1 Check if the power supply, as shown on the type

plate located on the bottom of the set,

corresponds to your local power supply. If it does

not, consult your dealer or service center.

2 If your set is equipped with a voltage selector,

adjust the selector so that it matches with the

local power .

3 Connect the power cord to the wall outlet.

4 To disconnect the power supply, unplug the set

from the wall outlet.

Auto-Standby mode

When a CD or tape has reached the end of playback

and remains in the stop position for more than

15 minutes, the set will switch off automatically to

save energy.

The type plate is located on the bottom of the

set.

BASIC FUNCTIONS

Switching on and off and selecting function

1 Press y on the set to switch on.

2 Press SOURCE once or more to select:

function.

TAPE

3 Press y to switch off the set.

Notes:

– To change from

when you are switching off the set: first, make

sure you press the tape STOP 9 key to end

playback and all the cassette keys are released.

– The tone, sound settings, tuner presets and the

volume level (up to a maximum volume level of 20)

will be retained in the set's memory.

Adjusting volume and sound

1 Adjust the volume with the VOLUME control.

™ Display shows the volume level and a number

from 0-32. (See 2)

2 Press DBB once or more to select dynamic bass

boost on or off.

™ Display: shows

3 To adjust the bass, mid and treble tones, press and

hold + or – on the BASS, MID, HIGH keys until

you reach the desired level, –5 to +5

™ Display briefly shows

level. (See 3)

Note: To prevent sound interference the bass control

options operate exclusively. You cannot combine the

bass from BASS with DBB

™ The display shows

automatically switched off to remind you if you

attempt to use both bass settings

Mute (for AZ2045 only)

1 Press MUTE on the remote control to interrupt

sound reproduction instantly.

™ Playback continues without sound and the

display flashes

2 To reactivate sound reproduction you can:

– press MUTE again;

– adjust the volume controls;

– change source.

DIGITAL TUNER

Tuning to radio stations

1 Press y to on, then press SOURCE to select

TUNER

–

is displayed briefly and then the radio station

frequency, waveband and, if programmed, a

TUNER

preset number are shown. (See 4)

2 Press BAND once or more to select your

waveband.

DIGITAL TUNER

TAPE

TUNER

when activated.

BASS

function, or

, or

and the

MID

HIGH

or the

indicator is