Dimplex AC3CN Manuel de l'utilisateur - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Dimplex AC3CN. Dimplex AC3CN 4 pages. Recessed ceiling heater/ over door heater
Également pour Dimplex AC3CN : Instructions (4 pages), Manuel de l'utilisateur (8 pages)

Imprimer la page

Recessed Ceiling Heater / Over Door Heater

Model: AC3CN

Model

(kW)

AC3CN

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Important Safety Advice

Warning - Disconnect from the mains supply before carrying out

maintenance.

DO NOT COVER OR OBSTRUCT the air inlet/outlet ceiling grille.

A minimum distance of 1.5 metres must be observed between the

ceiling grille and any furniture, combustible material or furnishings.

This appliance must not be installed less than 1.8 metres above the

ﬂ oor.

WARNING: ENSURE THIS PRODUCT IS EARTHED.

Ensure the supply cables are of adequate current carrying

capacity and are protected by a suitable fuse.

A suitable termination to the ﬁ xed wiring of the premises must be

provided adjacent to the ﬁ nal position of the Switch Panel.

This heater must not be located immediately above or below a ﬁ xed

socket outlet or connection box.

This product must not be subjected to water spray or immersion and

should be mounted such that no part of it can be touched by a person

using a ﬁ xed bath or shower.

DO NOT use the heater in the immediate surroundings of a bath, a

shower or a swimming pool.

DO NOT use this heater in areas where excessive dust exists.

This product should be mounted safely into ceiling areas only.

The ceiling can be either of a plasterboard (or similar) construction,

or of suspended 600 x 600mm ceiling tiles.

DO NOT store or use any ﬂ ammable materials or sprays in the vicinity

of the heater – FIRE HAZARD.

DO NOT insert any foreign objects into the heater openings.

Risk of injury, electric shock or damage to the heater may occur.

Ensure proper manual handling procedures are observed at all

times.

General

The carton contains: -

•

1 AC3CN heater

•

1 Ceiling grille assembly (frame + egg crate core)

•

1 Switch Box

This Recessed Ceiling Heater / Over Door Heater is a robust heater intended

for installation into a suspended or plasterboard ceiling.

For optimum results, do not install this product in ceilings higher than 3

metres. If multiple heaters are installed, generous spacing should be provided

between heaters to achieve an even heating distribution.

Electrical Connection

The Electrical Connection of this product should be carried out by a competent

electrician and be in accordance with the current IEE wiring regulations.

A suitable local isolating switch must be provided in the electrical supply circuit

with at least 3mm clearance on each pole.

Connection of Heater

Gain access to the terminal block

(see 'y' in Fig. 2) by removing the

access panel (see 'x' in Fig. 2)

and feeding an appropriate cable

through the cable gland.

Current

Voltage

(amps)

(volts)

∼ 230-240

Fig. 2

Weight

(kg)

8.7

Fig. 1

WARNING: Ensure power cable path does not come into contact with internal

heater elements or fans.

Make connections as per wiring Diagram (see Fig. 3) and replace the base

cover and access cover.

Label

Description

BLOWER MOTOR

HEATER ELEMENT

TERMINAL BLOCK

POWER CABLE FROM SWITCH PANEL (5 core - NOT SUPPLIED)

Connection of Switch Panel

The mains electrical supply cable and power cable to this heater (neither

supplied) should be connected as per the wiring diagram shown in

Fig. 4 (see Fig. 5 for Switch No.'s).

Label

Description

ON - OFF (Double Pole Switch)

HALF HEAT (Single Pole Switch)

SECOND HALF HEAT (Single Pole Switch)

TERMINAL BLOCK

POWER CABLE TO HEATER (5 core - NOT SUPPLIED)

MAINS IN POWER CABLE (NOT SUPPLIED)

∗ Test all switch settings once installation is complete ∗

Fig. 3

Fig. 4