Dimplex CMH Series Instructions d'installation - Page 3

Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} Dimplex CMH Series. Dimplex CMH Series 4 pages. Ceiling heater (with connex)
Également pour Dimplex CMH Series : Instructions d'installation (3 pages)

Imprimer la page

Dimplex CMH Series Instructions d'installation

Operation

Figure 3

WARNING: This heater is factory prewired for operation

with the built-in thermostat. THIS HEATER IS NOT TO BE

USED WITH A REGULAR WALL THERMOSTAT.

CAUTION: This heater must be properly installed before

it is used.

The CMH is designed with a two stage heating element that

will turn on and off based on the built-in temperature sensor to

maintain a constant room temperature.

NOTE: The element retains heat after shutdown, there is

a built in cool down period of 5 minutes before the fan shuts

off completely.

Manual Controls

(See Figure 3 for display reference)

When power is first supplied to the CMH the Setpoint Tem-

perature will flash in the temperature display area. At any time

either the ✚ or – button can be pressed to have the tempera-

ture setpoint displayed again.

A. Setting/Temperature Display

The CMH is designed to control the temperature of a room

from 41-104°F (5-40 °C). By pressing the ✚ or – will increase

or decrease the desired temperature for the room to be heated

by 0.5° (in either °C or °F).

When adjusting the Setpoint Temperature the display will

switch back to display the ambient temperature after 5 sec-

onds.

NOTE: The unit can be set to run continuously as a fan by

setting the temperature at 41 °F (5 °C). At this temperature

the heater will not turn on.

NOTE: Pressing the ✚ and – at the same time will toggle

between °C and °F.

B. Comfort Setting

The Comfort Setting icon will be displayed when the heater

is in normal operation based on the Setpoint Temperature for

the room.

NOTE: Either the

pendent on the setting being used.

C. Economy Setting

The Economy Setting can be used to change the Setpoint

Temperature for a user determined period of time. By pressing

the V the Economy Setting will be enabled - signified by the

A - Setting/Temperature Display

B - Comfort Setting Icon

C - Economy Setting Icon

D - Set Back Temperature Setting

E - Synchronized Icon

F - Lock Icon

G - Decrease Button

H - Increase Button

I - Menu Button

icon will always be visible, de-

icon flashing. After the Set Back Temperature has been set,

the icon will become solid after three seconds and the Set

Back Temperature will be enabled.

To return back to the Comfort Setting press the V button. The

icon will disappear and the

D. Set Back Temperature Setting

The Set Back Temperature Setting is used during periods

when the Economy setting feature is active. This temperature

adjustment can be set by pressing the V followed by the ✚ or

–.

E. Synchronized Icon

The CMH features CONNEX

works with Dimplex single and multi-zone CONNEX

lers to provide simple whole home connectivity and comfort.

CONNEX

controllers are available to control one or multiple

CONNEX

series heaters within a 50' (15 m) radius. In order

for the controller to have this function the CMH and the con-

troller will need to be synchronized. To do this:

1. On the CMH press and hold the V button for 3 seconds,

both the

and

2. Press the – , ✚ and then V, on the CMH.

3. Within 10 seconds press any button once on the

CONNEX

Controller.

NOTE: There is a 3 second delay between pressing the last

button on the controller and the CMH.

NOTE: To desynchronize a CMH from the synchronized

CONNEX

Controller; on either the CMH or the controller:

1. Press and hold the V for 3 seconds.

2. Press the V, ✚ and then –.

Nothing will need to be done to the other component.

Dimplex single and multi-zone CONNEX

separately and are available for purchase from your autho-

rized Dimplex dealer.

To find your local Dimplex dealer, visit www.dimplex.com.

F. Lock Icon

The CMH has a Lock feature to prevent settings from acciden-

tally being changed.

1. Press and hold the V for 3 seconds. Both the

Icons will begin to flash.

2. To Enable: Within 5 seconds press ✚, then –, then ✚,

then –. The

icon will appear

To Disable: Within 5 seconds press –, then ✚, then –,

then ✚. The

icon will disappear.

NOTE: The CMH can be locked in either the Comfort or

Economy Setting. Ensure that the desired icons are present

when locking is complete.

Boost Function

The CMH is also equipped with a "Boost Function" which al-

lows the user to run the unit at full heat, for a predetermined

amount of time, to quickly heat up a cold room/space. The

Boost can be set for a maximum of 20 minutes, in 5 minute

increments.

To enable Boost:

1. Press and hold ✚ for 5 seconds. The area where the tem-

perature normally displays will begin to toggle between

icon will appear.

, a wireless technology that

icons will begin to flash.

controllers are sold

control-

and