CRU DataPort 1U Manuel de démarrage rapide
Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} CRU DataPort 1U. CRU DataPort 1U 2 pages. Enclosure with digital cinema dx115s
Imprimer la pageDataPort®1U Enclosure with Digital Cinema DX115s
The DataPort®1U Enclosure with Digital Cinema DX115's supports up to 2 removable SATA hard drives. It is available in
SFF-8470 multilane and Port Multiplied eSATA interfaces, outlined below. Consult the manual for your host adapter to
determine which interface it requires.
Package Contents:
®
(1) DataPort
1U Enclosure w/ Digital Cinema
DX115 Frames*
(1) Power Cable
(4) HDD Mounting Screw Kits
(1) Rack Mount Screw Kit
*Carriers included in some assemblies.
Available Configurations
DataPort®1U with Single SFF-8470 multilane:
Supports removable drives on one connection, behaving as separate
SATA cables. Due to host adapter variations, the SFF-8470 assemblies
do not include the external enclosure to host cables. These are avail-
able through CRU's authorized resellers.
Available accessories for this configuration include:
External Cables:
• SFF-8470 (Multi-lane) to SFF-8470 (Multi-lane)
CRU Part # 7366-700-03
• SFF-8470 (Multi-Lane) to SFF-8088 (Mini-SAS)
CRU Part # 7366-701-01
Host Support:
• End to End Cable Assembly Kit
CRU Part # 7100-800-10
Includes:
• (1) 4x SATA to SFF-8470 (Multi-lane) PCI host adapter
• (4) Internal SATA cables
• (1) SFF-8470 (Multi-lane) to SFF-8470 (Multi-lane) external cable
DataPort®1U with Single Port Multiplied eSATA:
A single standard eSATA cable supports both removable disks. The host
bus adapter must be "Port Multiplier Aware" to use this technology,
Available accessories for this configuration include:
External Cables:
• 1 Meter eSATA to eSATA External Cable
CRU Part # 7380-1000-40
Host Support:
• eSATA 4-Port Host Adapter w/ Port Multiplier Support (PCI-X)
CRU Part # 30300-0500-0004
• eSATA 2-Port Host Adapter w/ Port Multiplier Support (PCIe)
CRU Part # 30310-0500-0002
Installing Hard Drives into the DX115 Carriers
1. To remove the carrier cover, remove the 2 screws on either side
and lift out.
2. Carefully insert the drive and slide towards the connector in the
rear so that it mates properly.
3. Hold the drive in place and turn the drive/carrier assembly over.
4. Fasten the drive into place with the four mounting screws provided.
(Some drives may require minor adjustments before mounting)
5. Replace the drive cover and secure with two screws removed in
step 1.
Enclosure Setup Instructions
WARNING: The DataPort
other support system to be rack mounted. The front mounting
brackets will not allow the DataPort 1U Enclosure to be rack
mounted without additional support.
1. Install universal 1U rails or appropriate support system compatible
with your rack mounting system.
2. Follow the instructions to install hard drives into the DX115 carriers.
3. Insert the removable carriers into the Digital Cinema DX115
frames.
4. Connect the host computer to the DataPort®1U with the appropriate
multi-lane or external SATA cable. (Cables purchased separately).
5. Power on using the switch located on the rear of the enclosure. For
best results power on the enclosure prior to powering on the host
system.
NOTE: The DataPort®1U Enclosure supports hot-swapping
of the drives in the removable drive carriers, provided the host
bus adapter supports that feature. When hot swapping drives,
ensure drive activity has stopped before removing the drive
carriers.
®
1U Enclosure requires slide rails or