3Com 3C888 - OfficeConnect Dual 56K LAN Modem Router Manuel de démarrage - Page 6

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage pour {nom_de_la_catégorie} 3Com 3C888 - OfficeConnect Dual 56K LAN Modem Router. 3Com 3C888 - OfficeConnect Dual 56K LAN Modem Router 6 pages. Dual 56k lan modem

Imprimer la page
T
ROUBLESHOOTING
The table below lists symptoms of common problems, possible causes, and possible solutions. For additional
troubleshooting information, refer to the User Guide located on the 3Com Companion Programs CD-ROM. For FAQs and
other technical notes, refer to the LAN Modem web site at:
Symptom
Possible Cause
Web browser does not
Web browser needs the IP
start (the welcome
address of the LAN Modem;
message does not
or the browser is not set to a
appear).
default start page
Incompatible IP address on
your computer.
Web browser may be
configured to use a proxy
server.
There is a configuration
problem.
At installation, LAN LED
Wrong cable used to connect
does not light up.
your computer to the LAN
Modem's LAN port.
At installation, ALERT
An internal failure.
LED remains lit.
At installation, ALERT
Self-test failure, or LAN
LED continues to flash.
Modem is in firmware
download mode
No dial tone when
Telephone line cables, power
handset of a phone
cable, and/or phone cables
attached to unit is lifted.
may not be firmly connected.
Telephone line cables may
not be in the correct ports.
Data call may be in progress.
Cannot place test call to
ISP not properly configured.
the Internet
Phone line not connected.
3Com Corporation, 5400 Bayfront Plaza, Santa Clara, California, 95052-8145
© 3Com Corporation, 2000. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation,
transformation, or adaptation) without permission from 3Com Corporation. 3Com Corporation reserves the right to revise this documentation and to make changes in content from time
to time without obligation on the part of 3Com Corporation to provide notification of such revision or change. 3Com Corporation provides this documentation without warranty of any
kind, either implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. 3Com may make improvements or changes in
the product(s) and/or the program(s) described in this documentation at any time.
UNITED STATES GOVERNMENT LEGEND;
For units of the Department of Defense:
The Software is commercial computer software as defined in 48 C.F.R. 211 and therefore is provided to units of the Department of Defense under the terms of this License Agreement,
which is 3Com's standard commercial agreement for the Software. In the alternative, if 48 C.F.R. 211 is not invoked, the Software is licensed as follows: Restricted Rights Legend: Use,
duplication or disclosure by the United States Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software Clause at
48 C.F.R. 52.227-7013. 3Com Corporation, 5400 Bayfront Plaza, Santa Clara, California 95052-8145.
For civilian agencies:
Restricted Rights Legend: Use, reproduction or disclosure is subject to restrictions set forth in subparagraph (a) through (d) of the Commercial Computer Software - Restricted Rights clause
at 48 C.F.R. 52.227-19 and the limitations set forth in 3Com's standard commercial agreement for the Software. Unpublished rights reserved under the copyright laws of the United States.
If there is any software on removable media described in this documentation, it is furnished under a licence agreement included with the product as a separate document, in the hard copy
documentation. If you are unable to locate a copy, please contact 3Com and a copy will be provided to you.
Unless otherwise indicated, 3Com registered trademarks are registered in the United States and may or may not be registered in other countries.
3Com and OfficeConnect are registered trademarks of 3Com Corporation.
Acrobat and Adobe are registered trademarks of Adobe Systems, Incorporated. Macintosh is a registered trademark of Apple Computer. Pentium is a registered trademark of Intel
Corporation. Windows and Windows NT are registered trademarks of Microsoft. Netscape Navigator is a registered trademark of Netscape Communications.
Other brand and product names may be registered trademarks or trademarks of their respective holders.
Environmental Statement
It is a 3Com policy to be environmentally friendly in all operations. This manual is printed on paper that comes from sustainable, managed European forests. The production process for
making the pulp has a reduced AOX level (absorbable organic halogen) resulting in elemental chlorine-free paper. This paper is fully biodegradable and recyclable.
http://www.3com.com/support/docs/lanmodem/
Solution
1 Enter the following URL in your Web browser:
natively, you can enter
http://192.168.1.1.
2 Run the EZ-LAN Wizard, or refer to Chapter 3 of the User Guide.
3 Reset the IP address on your computer, as follows:
Windows 95 and 98: Run winipcfg.exe. Select the Ethernet adapter connected to the Dual
56K LAN Modem. Click Release All and then Renew All.
Windows NT 4.0/2000: Run ipconfig /release and then ipconfig /renew.
Macintosh: From Apple menu, select Control Panels; then TCP/IP. In the Connect via field, make
sure Ethernet is selected. In the Configure field, select Using Bootp Server to clear the fields. Close
and save changes. Re-open the TCP/IP control panel, and select Using DHCP Server. The fields
should now read <will be supplied by server>. Select File, then Close, saving changes.
Set the browser to use the LAN Modem, as follows:
Internet Explorer: From the View menu, choose Internet Options. Click the Connection tab.
Uncheck the box labeled Connect using Proxy server.
Netscape: From the Edit menu, choose Preferences. Under Advanced, choose Proxies. Check the
box labeled Direct Connection to the Internet.
Reset the Dual 56K LAN Modem to the factory default setting as follows
Press and release the reset button located on the back of the unit. The Alert LED will begin to
flash. While the LED is still flashing, press and continue to hold in the reset button on the back
of the unit. (You must continuously hold the reset button through three cycles of LED
flashing: Reset, Firmware Download Mode, and Factory Default Reset.) After the ALERT LED
has flashed for the third cycle, you have successfully reset the LAN Modem back to factory
defaults. Release the reset button.
The LAN Modem reinitializes itself and is reset to the factory defaults. All user-entered information
will be erased. Restart your computer and launch your Web browser.
Make sure you are using the RJ-45 to RJ-45 cable labeled Ethernet which was provided with your
Dual 56K LAN Modem. If you are using another 10BASE-T Ethernet (Category 5) cable, it must be a
straight-through cable.
Notify your reseller or technical support that the Dual 56K LAN Modem has failed the self-test.
Power-cycle the Dual 56K LAN Modem. If the ALERT LED continues to flash, the Dual 56K LAN
Modem has failed the self-test. Contact your reseller or technical support. If the ALERT LED is not
flashing, then the LAN Modem is now operating correctly.
Check all cables and connectors to ensure that they are inserted securely.
Ensure that the incoming analog telephone line cables have been connected to the ports labeled
LINE 1 and LINE 2 on the Dual 56K LAN Modem's back panel. If using a single analog line, connect
to Line 1.
Disconnect any data calls currently in progress.
Confirm your ISP connection settings, such as Username, Password, and telephone number. Follow
steps 7-11 on page 4.
Check all cables and make sure that telephone line is connected to the Line 1 port.
6
Alter-
http://3com.oc.lanmodem.
: