Dimplex CDFI1000-PRO Manuel d'entretien - Page 12

Parcourez en ligne ou téléchargez le pdf Manuel d'entretien pour {nom_de_la_catégorie} Dimplex CDFI1000-PRO. Dimplex CDFI1000-PRO 18 pages.

Imprimer la page

Secondary Side

1. Disconnect and remove the media tray or log set from

the unit and put them in a safe place.

2. Remove the 4 screws and the electronics cover from

the unit. (Figure 4)

NOTE: Use caution when removing the electronics cov-

er, to prevent strain on the connector wire attached to it.

3. Holding the assembly at either end of the LED light

strip, on the primary end, gently lift the electronics as-

sembly out of the unit (Figure 4).

4. Gently lift the LED light assembly off of the standoffs.

5. Trace the control wire back to the main control board

and replace with the wire from the new assembly.

6. Install the new LED light assembly, ensuring that all

of the wires are installed in the same location as the

previous one.

7. Replace all of the wiring to their original locations and

reinsert the electronics assembly.

CAUTION: Ensure that the switchboard and terminal

block have not moved from their original locations and all

wires are contained under the cover before reassembly.

8. Re-assemble the remainder of the cassette in reverse

order from the instructions above.

Heating Element Replacement

Tools Required: Phillips head screwdriver

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or

damage to persons.

NOTE: Ensure that all of the components that contain

water have been emptied and source water has been

turned off before performing any maintenance.

Primary Side

1. Disconnect and remove the media tray or log set from

the unit and put them in a safe place.

2. Remove the securing screws and metal wire cover at

the end of both of the electronics covers.

3. Remove the 4 screws and both of the electronics cov-

ers from the unit. (Figure 4)

NOTE: Use caution when removing the electronics cov-

er, to prevent strain on the connector wire attached to it.

4. Remove the cable clamp, to allow for the assembly to

be lifted out to better access the components.

5. Holding the assembly at either end of the LED light

strip, on the primary end, gently lift the electronics as-

sembly out of the unit (Figure 4).

NOTE: There are several wires that run between the

two sides, these wires will need to be gently removed

through the opening on the secondary side to allow the

primary electronics assembly to be lifted out.

6. Locate the 2 screws that secure the element assembly

(element and brackets) to the unit and remove.

7. Lift the element assembly out of the unit.

8. Disconnect the element from the main control board.

9. Remove the element from the mounting bracket and

install the new element.

10. Attach the new element to the main control board.

11. Install and secure the element assembly into the unit.

12. Replace all of the wiring to their original locations and

reinsert the electronics assembly.

CAUTION: Ensure that the switchboard and terminal

block have not moved from their original locations and all

wires are contained under the cover before reassembly.

13. Re-assemble the remainder of the cassette in reverse

order from the instructions above.

Secondary Side

1. Disconnect and remove the media tray or log set from

the unit and put them in a safe place.

2. Remove the 4 screws and the electronics cover from

the unit. (Figure 4)

NOTE: Use caution when removing the electronics cov-

er, to prevent strain on the connector wire attached to it.

3. Holding the assembly at either end of the LED light

strip, on the primary end, gently lift the electronics as-

sembly out of the unit (Figure 4).

4. Locate the 2 screws that secure the element assembly

(element and brackets) to the unit and remove.

5. Lift the element assembly out of the unit.

6. Disconnect the element from the main control board.

7. Remove the element from the mounting bracket and

install the new element.

8. Attach the new element to the main control board.

9. Install and secure the element assembly into the unit.

10. Replace all of the wiring to their original locations and

reinsert the electronics assembly.

CAUTION: Ensure that the switchboard and terminal

block have not moved from their original locations and all

wires are contained under the cover before reassembly.

11. Re-assemble the remainder of the cassette in reverse

order from the instructions above.