Dimplex Wall Fire SP4 Manuel d'installation et d'utilisation - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel d'installation et d'utilisation pour {nom_de_la_catégorie} Dimplex Wall Fire SP4. Dimplex Wall Fire SP4 9 pages. Dimplex indoor fireplace user manual

Imprimer la page

Dimplex Wall Fire SP4 Manuel d'installation et d'utilisation

Remote Control Operation

General

The remote control consists of 5 control buttons and a LCD

display with a visible area of 40x40mm.

The maximum range of use for the remote control is 15metres.

LCD display

The LCD display shows the following functions:

•

Main menu points: OFF, FLAME, HEAT, TEMP, TIMER,

PROG, and TIME.

•

Brightness of the flame effect shown as a bar chart in 4

steps (50 steps internally).

•

Remote control set temperature in °C (thermostat

function).

•

Room temperature

•

Selectable heat settings LOW HEAT / OFF.

•

Time display in format hh:mm – shown as 24hr.

•

Weekdays MON, TUE, WED, THU, FRI, SAT, SUN.

Menu functions

•

OFF

switching off of all functions (stand-by mode).

•

FLAME

switching on the flame effect from 0 (off) to

50 (max. brightness).

•

HEAT

setting the desired heat position from 0 (off)

to 1 (low heat).

•

TEMP

preselection of the remote control set

temperature from 5°C to 35°C.

•

TIMER

selection of the run back timer function (from

1 minute to 4 hours 59 minutes). When the selected time

is over the unit will be in stand-by mode.

•

PROG

selection of the programming mode. 32

individual programs can be entered. This is a week timer

where all functions of the unit can be checked time

controlled.

•

TIME

setting the time and the weekdays.

First steps

•

Fit batteries supplied.

•

Press switch 1 to ON (see Fig. 6).

•

Press switch 2 to AUTO (see Fig. 6)

The remote control is now ready.

Operating Instructions

•

Switching ON/OFF

The heater can be switched on by pressing the enter

buttons.

The heater can be switched off by moving the cursor to the

OFF menu item.

•

Flame brightness

Navigate the cursor to FLAME with the

- - - - - to change the brightness of the fire effect from off (0) to

maximum (50).

Fig. 8

LCD Display

in °C .

buttons. Press

•

Heat settings

Navigate the cursor to HEAT with the

- - - - - to change the heat setting between off/low heat.

Note: If the room temperature

control set temperature located on the left side of LCD display,

heat will not come on (see Thermostat operation below).

•

Thermostat

Navigate the cursor to TEMP with the

- - - - - to set the desired remote control set temperature between

5°C and 35°C and press enter

ture

is higher than the remote control set temperature,

the heater switches off automatically until the room tempera-

ture

falls below the remote control set temperature.

•

Runback timer

Navigate the cursor to TIMER with the

hours (0 to 4) with

minutes (0 to 59) with

runback timer is activated (the symbol TIMER appears) and

will switch the heater off automatically when the pre-set time

is over.

•

Time setting

Navigate the cursor to TIME with the

enter button

Confirm with the enter button

- - - - - . Press enter

with

•

Program mode

Navigate the cursor to PROG with the

press enter . Choose a program number between 1 and

32 with the

Set the days with

Saturday and Sunday or Monday until Sunday can be

chosen. Press the enter button

Set the program start time with

hours and minutes with the enter button

Set the program stop time with

hours and minutes with the enter button

Set the remote control set temperature with

confirm with the enter button

Set the brightness of the fire effect with

50 and confirm with the enter button

Set the heat setting between off/low heat/maximum heat

with the

All settings for the first program are done now. Enter a

new program according to the steps 1-8 or activate the

already entered program by leaving of this menu with

the

button.

Now the program mode is active, the symbol PROG

appears. The heater operates according to the entered

information. While the program mode is activated, the

start and stop time, the active program number and the

remote control set temperature and the room temperature

will be displayed alternating.

10. An entered program can be checked, edited and deleted

just by navigating again into the PROG menu and

pressing the enter button. With the

different program numbers can be selected. To delete

one program number, press the

(clear program) appears and by pressing the enter button

the current program will be deleted.

menu without deleting the program.

is higher than the remote

. When the room tempera-

- - - - - and press enter

to adjust the weekday with the

and set the hours and minutes

to leave the time menu.

- - - - -

buttons and press enter

- - - - - . Single days, Monday until Friday,

to accept.

- - - - - button and confirm with the enter button

button. The CP symbol

buttons. Press

buttons. Set the

. Then set the

. Now the

buttons. Press the

- - - - - buttons.

, buttons and

- - - - -

and confirm the

- - - - -

and confirm the

- - - - - and

- - - - - from 0 to

- - - - - buttons the

leaves the