Pioneer P770MP - Premier In-Dash CD/MP3/WMA/WAV Receiver Manuel d'installation - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} Pioneer P770MP - Premier In-Dash CD/MP3/WMA/WAV Receiver. Pioneer P770MP - Premier In-Dash CD/MP3/WMA/WAV Receiver 6 pages. Pioneer deh-p770mp: install guide

Imprimer la page

Pioneer P770MP - Premier In-Dash CD/MP3/WMA/WAV Receiver Manuel d'installation

Connecting the Units

7 When using a Subwoofer without using the optional amplifier

IP-BUS input

(Blue)

This product

Front output

Subwoofer output

Fuse

Antenna jack

Yellow/black

If you use a cellular telephone, connect it via the

Audio Mute lead on the cellular telephone. If not,

keep the Audio Mute lead free of any connections.

Yellow

To terminal always supplied with power regardless of

ignition switch position.

Red

To electric terminal controlled by ignition switch (12

V DC) ON/OFF.

Orange/white

To lighting switch terminal.

Black (ground)

To vehicle (metal) body.

Rear output

16 cm (6-1/4 in.)

Jack for the Wired Remote Control

Please see the Instruction Manual for the

Wired Remote Control (sold separately).

Multi-CD player

IP-BUS cable

(sold separately)

Blue/white

To system control terminal of the power amp or

Auto-antenna relay control terminal (max. 300

mA 12 V DC).

White

Gray

Front speaker

≠

White/black

Gray/black

Left

Green

Violet

Subwoofer

≠

Green/black

Violet/black

Note:

Change the initial setting of this unit (refer to the Operation

Manual). The subwoofer output of this unit is monaural.

Installation

Note:

• Before making a final installation of the unit, tem-

porarily connect the wiring to confirm that the con-

nections are correct and the system works

properly.

• Use only the parts included with the unit to ensure

proper installation. The use of unauthorized parts

can cause malfunctions.

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifications

of the vehicle.

• Install the unit where it does not get in the driver's

way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

• The semiconductor laser will be damaged if it

overheats, so don't install the unit anywhere hot

— for instance, near a heater outlet.

DIN Front/Rear-mount

This unit can be properly installed either from "Front" (conventional DIN Front-mount) or

"Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit

chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 5)

Front speaker

Dashboard

182

Right

Subwoofer

Fig. 3

Removing the unit (Fig. 6) (Fig. 7)

• If installation angle exceeds 60° from horizontal,

the unit might not give its optimum performance.

(Fig. 4)

60°

Fig. 4

Holder

After inserting the holder into the

dashboard, then select the appropriate

tabs according to the thickness of the

dashboard material and bend them.

(Install as firmly as possible using the

top and bottom tabs. To secure, bend

the tabs 90 degrees.)

Rubber bush

Screw

Fig. 5

Frame

To remove the frame, extend top and

bottom of the frame outwards in

order to unlock it. (When reattaching

the frame, point the side with a

groove downwards and attach it.)

• It becomes easy to remove the

frame if the front panel is released.

Fig. 6

Insert the supplied extraction keys

into the unit, as shown in the figure,

until they click into place. Keeping

the keys pressed against the sides of

the unit, pull the unit out.

Fig. 7