Ariston AB 103 M Manuel d'instructions pour l'installation et l'utilisation - Page 26
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions pour l'installation et l'utilisation pour {nom_de_la_catégorie} Ariston AB 103 M. Ariston AB 103 M 32 pages. Margherita
Également pour Ariston AB 103 M : Manuel d'instructions pour l'installation et l'utilisation (32 pages)
Imprimer la page
M
ARGHERITA
The washing machine
does not drain or
spin.
Does
the
selected
programme foresee water
draining? Some wash cycles
require enabling the draining
manually.
Is the Anti-crease"
function -where provided -
enabled? This function require
enabling the draining
manually.
Is the drain pump clogged?
To check it, close the tap,
unplug the washing machine
and follow the instructions on
page 25, or call for technical
assistance.
Always get
assistance from
authorised
technicians and
always insist on
original spare
parts.
Technical characteristics
AB 103 M
Model
width 59,5 cm
Dimensions
height 85 cm
depth 52,5 cm
from 1 to 5 kg
Capacity
voltage 220/230 Volt 50 Hz
Electrical
maximum absorbed power 1850 W
connections
maximum pressure 1 MPa (10 bar)
Water
minimum pressure 0,05 MPa (0,5 bar)
connections
drum capacity 40 litre
up to 1000 rpm
Spinning speed
programme 3; temperature 60°C; press Extra economy button; carried out with 5 kg load.
Control programs
in compliance
with IEC
regulation 456
This appliance conforms with the following E.E.C. directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications
TS 2004 EN 60335-2-7
23
Margherita - Instructions for installation and use
All manuals and user guides at all-guides.com
Is the drain hose bent? The
tract of the drain hose must be
as straight as possible. Make
sure it is not squashed or bent.
Is the washing machines
drain duct clogged? Is there
an extension of the drain
hose? If so, is it positioned
incorrectly, blocking the water
flow?
The washing machine
vibrates too much
during the spin cycle.
Has the internal floating
unit been correctly
unblocked
during
installation? See the
following page on installation
procedures.
Has the washing machine
been levelled correctly? The
levelling of the appliance
should
be
checked
periodically. In time, the
machine
could
move
imperceptibly. Adjust the feet
and check them with a level.
Is the appliance closed in
between furniture and a
wall? If it is not a built-in
model, the washing machine
needs to oscillate a bit during
the spin cycle. A few cm of
space should therefore be left
around it.
The washing machine
leaks.
Is the metal ring of the inlet
hose properly attached?
Close the tap, unplug the
appliance and try tightening its
attachment without forcing it.
Is the detergent dispenser
obstructed? Try extracting it
and washing it under tap
water.
Is the drain hose well
attached? Close the tap,
unplug the appliance and try
tightening its attachment.
Too much foam.
Is the detergent appropriate
for machine washing? Check
whether its label reads the
definition for machine wash
or hand and machine wash,
or other similar indications.
Is the correct amount being
used? An excessive amount of
detergent, besides producing
too much foam, does not
guarantee a more effective
wash, and causes scaling in the
internal parts of the appliance.
If, despite all checks, the
washing machine fails to
function and the problem
persists, call your nearest
authorised Customer Service
Centre, providing the following
information:
- the type of malfunctioning
- the model type no. (Mod. ....)
- the serial number (S/N ....)
These indications can be found
on the data plate situated on the
back of the washing machine.