Pioneer GM-D8400M - Amplifier Manuel du propriétaire - Page 3
Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} Pioneer GM-D8400M - Amplifier. Pioneer GM-D8400M - Amplifier 6 pages. Class d mono amplifier
Également pour Pioneer GM-D8400M - Amplifier : Manuel du propriétaire (38 pages), Manuel du propriétaire (16 pages), Manuel d'entretien (32 pages)
Imprimer la page
Connecting the Unit
ENGLISH
7 Connections when using the speaker
Connecting the Speaker Output
input
Terminals
• Use a 10 AWG to 16 AWG wire for the speaker
wire.
1. Expose the end of the speaker wires
Car Stereo
using nippers or a cutter by about
10 mm to 12 mm.
10 mm to 12 mm
White:
Black:
Black:
Left + Left ≠
Right ≠ Right +
2. Connect the speaker wires to the
speaker output terminals.
• Fix the speaker wires securely with the termi-
nal screws.
Terminal screws
Speaker output
To RCA input
terminal
jack of this unit.
Speaker wire
Connecting the Speaker Wires
Using the Speaker Input
Connect the speaker leads according to the
figures shown below.
Connect the car stereo speaker output
wires to the amplifier using the supplied
speaker input wire with RCA pin cord.
• Slide the input switch to the left (SP).
Installation
CAUTION
• Do not install in:
To prevent malfunction and/or injury
—Places where it could injure the driver or pas-
• To ensure proper heat dissipation of the amplifier,
sengers if the vehicle stops suddenly.
be sure of the following during installation.
—Places where it may interfere with the driver,
such as on the floor in front of the driver's
seat.
• Make sure that wires are not caught in the sliding
mechanism of the seats, resulting in a short-cir-
• DO NOT allow amplifier to come into contact
cuit.
Speaker output
with liquids due to, for example, the location
• Confirm that no parts are behind the panel when
where the amplifier is installed. Electrical shock
drilling a hole for installation of the amplifier.
could result. Also, amplifier and speaker damage,
Protect all cables and important equipment such
smoke, and overheating could result from contact
as fuel lines, brake lines and electrical wiring
with liquids. In addition, the amplifier surface and
from damage.
Red:
the surface of any attached speakers could become
• Install tapping screws in such a way that the screw
hot to the touch and minor burns could result.
tip does not touch any wire. This is important to
• Do not install the amplifier on unstable places
prevent wires from being cut by vibration of the
such as the spare tire board.
car, which can result in fire.
• The best location for installation differs with the
• DO NOT allow amplifier to come into contact
car model and installation location. Secure the
with liquids due to, for example, the location
Speaker input
amplifier at a sufficiently rigid location.
where the amplifier is installed. Electrical shock
• Make temporary connections first and check that
wire with RCA
could result. Also, amplifier and speaker damage,
the amplifier and the system operate properly.
pin cord
smoke, and overheating could result from contact
• After installing the amplifier, confirm that the
with liquids. In addition, the amplifier surface and
spare tire, jack and tools can be easily removed.
the surface of any attached speakers could become
hot to the touch and minor burns could result.
• To ensure proper installation, use the supplied
parts in the manner specified. If any parts other
than the supplied ones are used, they may damage
internal parts of the amplifier, or they may
become loose causing the amplifier to shut down.
• Never replace the fuse with one of greater value
or rating than the original fuse. Use of an improp-
er fuse could result in overheating and smoke and
could cause damage to the product and injury
including burns.
Subwoofer
Attaching the Bass boost remote
CAUTION:
control
Attach with tapping screws (3 mm × 10 mm) at an
easily accessible location such as under the dash-
board.
—Allow adequate space above the amplifier for
proper ventilation.
—Do not cover the amplifier with a floor mat or
carpet.
Tapping screw
(3 mm × 10 mm)
ENGLISH
Specifications
Example of installation on the floor
Power source............................................................................................................ 14.4 V DC (10.8 V to 15.1 V allowable)
Grounding system ............................................................................................................................................ Negative type
mat or on the chassis
Current consumption ........................................................................................................ 27.0 A (at continuous power, 4 Ω)
Average current drawn* .............................................................................................................. 7.5A (4 Ω for one channel)
1. Place the amplifier where it is to be
Fuse .......................................................................................................................................................................... 30 A × 2
installed. Insert the supplied tapping
Dimensions .......................................................................................................... 290 mm (W) × 56 mm (H) × 200 mm (D)
screws (4 mm × 18 mm) into the
screw holes. Push on the screws with
Weight ...................................................................................................................... 3.2 kg (Leads for wiring not included)
Maximum power output ............................................................................................ 600 W × 1 (4 Ω) / 1 200 W × 1 (2 Ω)
a screwdriver so they make marks
Continuous power (14.4 V) .................................................................... 4 Ω, 20 Hz to 240 Hz,
where the installation holes are to be
located.
Load impedance .......................................................................................................................... 4 Ω (2 Ω to 8 Ω allowable)
Frequency response ............................................................................................................ 10 Hz to 240 Hz (+0 dB, –3 dB)
2. Drill 2.5 mm diameter holes at the
Signal-to-noise ratio ........................................................................................................................ 80 dB (IEC-A network)
point marked, and install the ampli-
Distortion .............................................................................................................................................. 0.3% (10 W, 100 Hz)
Low pass filter .............................................................................................................. Cut off frequency: 40 Hz to 240 Hz
fier, either on the carpet or directly
to the chassis.
Bass Boost .................................................................................................................................................. Frequency: 50 Hz
Tapping screw
(4 mm × 30 mm)
Gain control ...................................................................................................................................... RCA: 200 mV to 6.5 V
Maximum input level / impedance ........................................................................................................ RCA: 6.5 V / 22 kΩ
Note:
• Specifications and the design are subject to possible modification without notice
due to improvements.
*Average current drawn
• The average current drawn is nearly the maximum current drawn by this unit
when an audio signal is input. Use this value when working out total current
drawn by multiple power amplifiers.
Floor mat
or chassis
Drill a 2.5 mm diameter hole
ENGLISH
15.0 A (2 Ω for one channel)
(Terminals not included)
1.0 % THD, 300 W × 1
2 Ω, 50 Hz,
1.0 % THD, 600 W × 1
Cut off slope: –12 dB/oct
Level: 0 dB to 12 dB
Speaker: 0.8 V to 26 V
Speaker: 26 V / 90 kΩ