Pioneer DEH-6400BT Manuel du propriétaire - Page 14
Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} Pioneer DEH-6400BT. Pioneer DEH-6400BT 25 pages. Cd rds receiver
Également pour Pioneer DEH-6400BT : Manuel d'utilisation (36 pages), Manuel de démarrage rapide (8 pages)
Imprimer la page
Section
03
Installation
This unit
3
1
2
4 5
6
7
8
1 Power cord input
2 Microphone input
3 Microphone
4 Rear output or subwoofer output
5 Front output
6 Antenna input
7 Fuse (10 A)
8 Wired remote input
Hard-wired remote control adaptor can be
connected (sold separately).
Power cord
Perform these connections when not connect-
ing a rear speaker lead to a subwoofer.
1
2
3
4
6
8
7
9
5
c
b
d
e
f
g
h
14
En
Perform these connections when using a sub-
woofer without the optional amplifier.
1
2
3
4
6
8
7
9
i
c
b
d
e
j
f
c
g
k
l
h
b
d
1 To power cord input
2 Left
3 Right
4 Front speaker
5 Rear speaker
6 White
7 White/black
8 Gray
9 Gray/black
a Green
b Green/black
c Violet
d Violet/black
e Black (chassis ground)
Connect to a clean, paint-free metal location.
f Yellow
Connect to the constant 12 V supply termi-
nal.
g Red
Connect to terminal controlled by ignition
switch (12 V DC).
h Blue/white
Connect to system control terminal of the
power amp or auto-antenna relay control ter-
minal (max. 300 mA 12 V DC).
i Subwoofer (4 Ω)
Installation
j When using a subwoofer of 70 W (2 Ω), be
sure to connect the subwoofer to the violet
and violet/black leads of this unit. Do not
connect anything to the green and green/
black leads.
k Not used.
l Subwoofer (4 Ω)× 2
Notes
With a 2 speaker system, do not connect any-
thing to the speaker leads that are not con-
nected to speakers.
Change the initial setting of this unit. Refer
to REAR-SP (rear output setting) on page 11.
Refer to PREOUT (preout setting) on page 11.
The subwoofer output of this unit is monau-
ral.
Power amp (sold separately)
Perform these connections when using the op-
tional amplifier.
3
1
2
4
5
5
3
2
1
6
7
7
1 System remote control
Connect to Blue/white cable.
2 Power amp (sold separately)
3 Connect with RCA cables (sold separately)
4 To Front output
5 Front speaker
6 To Rear output or subwoofer output
7 Rear speaker or subwoofer
Installation
Important
Check all connections and systems before
final installation.
Do not use unauthorized parts as this may
cause malfunctions.
Consult your dealer if installation requires
drilling of holes or other modifications to the
vehicle.
Do not install this unit where:
it may interfere with operation of the vehicle.
it may cause injury to a passenger as a result
of a sudden stop.
The semiconductor laser will be damaged if
it overheats. Install this unit away from hot
places such as near the heater outlet.
Optimum performance is obtained when the
unit is installed at an angle of less than 60°.
60°
DIN front/rear mount
This unit can be properly installed using either
front-mount or rear-mount installation.
Use commercially available parts when instal-
ling.
DIN Front-mount
1
Insert the mounting sleeve into the dash-
board.
For installation in shallow spaces, use the sup-
plied mounting sleeve. If there is enough space,
use the mounting sleeve that came with the ve-
hicle.