Pioneer PDR-509 Manuel d'utilisation - Page 38

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Pioneer PDR-509. Pioneer PDR-509 40 pages. Compact disc recorder
Également pour Pioneer PDR-509 : Schémas de service (23 pages), Manuel d'entretien (48 pages), Manuel d'entretien (23 pages), Manuel d'entretien (14 pages)

Imprimer la page

Additional Information

It's often easy to mistake incorrect operation for trouble and malfunction of the unit. If you think there is something wrong

with the component, check the points below first. If the problem persists, contact you nearest Pioneer-authorized service

center and have them check over the unit.

Symptom

Power cannot be turned

on.

No sound is heard

during playback.

Cannot record.

Recorded sound is

distorted.

Remote control opera-

tion is impossible.

Some tracks are skipped

without being played.

Skip playback does not

occur.

A recorded

–

disc

cannot be played on

other

players.

The point-of-sale

demonstration is

displayed.

If digital synchro-recording fails to operate correctly, check the following:

1. Pause playback of the source, then press the DIGITAL SYNCHRO button again.

÷ If you're recording from a portable CD player, etc., make sure that the shock-protection feature is

switched off.

2. Start playback of the source component once you see the SYNCHRO indicator start to blink.

3. If none of the above solves the problem, use manual digital recording to record.

÷ Digital synchro-recording uses a digital sub-signal contained in the source player's digital output. Digital

synchro-recording will not work when recording from the following devices:

÷ CD players whose digital output does not include a sub-signal

÷ Portable CD, MD or DVD players which do not output a digital signal when stopped.

Cause

The power cord is unplugged from the wall

outlet.

The power was turned off from the compo-

nent (stereo amplifier, audio timer, etc.) to

which it is connected.

The recorder is not connected up properly.

The

–

disc in use has already

been finalized.

The input selection is incorrect.

The

control is set too low.

REC LEVEL

The ecording level is set too high.

Signal connections are incorrect.

There is interference from a TV set.

The disc is damaged or warped.

The disc is extremely dirty.

The remote control batteries are exhausted.

There is an obstacle between the remote

control unit and main unit.

The remote control unit is being operated

outside the remote controllable range.

The

button is set to on.

SKIP PLAY

The

button is set to off.

SKIP PLAY

The disc has not been finalized after

recording. When such a disc is loaded in the

unit, the

–

indicator lights.

The pickup lens of the other

dirty, impairing its ability to play

See page 36 for instructions on how to cancel

the store demo mode.

Remedy

Plug the power cord into a power outlet.

Turn on the component supplying the

power to the recorder.

Check all connections, especially to the

amplifier—pp.10–11

Check all connections— pp.10–11

Use a non-finalized disc or erase the

–

Select the input connected to the source

component you're recording from.

Increase the recording level— pp.24–25

Reduce the recording level—pp.24–25

Check all connections— pp.10–11

Turn the

further away from the

Use another disc.

Clean the disc.

Replace both of the remote control

batteries with new ones.

Remove the obstacle.

Operate in the remote controllable

range—p.14

Set the

SKIP PLAY

Set the

SKIP PLAY

Finalize the disc— p.33

player is

Try the disc on a different

–

discs.

plays

original player cleaned.

disc— pp.34–35

power off or install this unit

button to off—p.27

button to on —p.27

player. If it

then get the pickup lens on the