Pioneer Elite PRO-800HDI Manuel d'utilisation - Page 10
Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Pioneer Elite PRO-800HDI. Pioneer Elite PRO-800HDI 48 pages. Pioneer 3rd, 4th % 5th generations plasma panel quick reference parts lists
Également pour Pioneer Elite PRO-800HDI : Listes de référence rapide des pièces (12 pages)
Imprimer la page
Part Names and Functions
Connection Panel
The connection panel is provided with four video input
terminals and two video output terminals. Audio input and
speaker output terminals are also provided, together with
a CONTROL IN/OUT connector for connecting to
PIONEER components bearing the Î mark.
For instructions regarding connections, consult the pages
noted in parentheses by each item.
1
SPEAKER (R) terminal
For connection of an external right speaker.
Connect a speaker whose impedance is 8 –16
(page 14).
2
CONTROL IN/OUT (monaural mini jacks)
For connection of PIONEER components that bear the
Î mark. Making CONTROL connection enables
control of this unit as a component in a system
(page 16).
3
COMBINATION IN/OUT
DO NOT MAKE ANY CONNECTIONS TO THESE
TERMINALS.
These terminals are used in the factory setup.
4
RS-232C
DO NOT MAKE ANY CONNECTIONS TO THIS
TERMINAL.
This terminal is used in the factory setup.
Operating range of the remote control unit
When operating the remote control unit, point it at the remote sensor
(Î) located on the front panel of the main unit. The remote control
unit is operable up to 23 feet (7 m) from the unit and within a 30
angle on each side of the sensor.
If you are having difficulty with operation of the remote
control unit
¶ The remote control unit may not operate if there are objects placed
between it and the display.
¶ Operational distance will gradually become shorter as the batteries begin
to wear out, replace weak batteries with new ones as soon as possible.
¶ This unit discharges infrared rays from the screen. Placing a video deck or
other component that is operated by an infrared remote control unit near
this unit may hamper that component's reception of the remote control's
signal, or prevent it from receiving the signal entirely. Should this occur,
move the component to a position further away from this unit.
¶ Depending on the installation surroundings, this unit's remote control unit
may be influenced by the infrared rays discharged from the plasma display,
hampering reception of its rays or limiting its operational distance. The
strength of infrared rays discharged from the screen will differ according
to the picture displayed.
6
I
I
PRO-1000HD
/ PRO-800HD
5
INPUT1 (mini D-sub 15 pin)
For connection of components that have RGB or
component output jacks such as a personal
computer, DVD player, or external RGB decoder.
Make sure that the connection made corresponds to
the format of the signal output from the connected
component (pages 9 to 12).
6
OUTPUT (INPUT1) (mini D-sub 15 pin)
Use the OUTPUT (INPUT1) terminal to output the
video signal to an external monitor or other
component.
Note: The video signal will not be output from the
OUTPUT (INPUT1) terminal when the main power of
this unit is off or in standby mode.
(page 11)
7
INPUT2 (BNC jacks)
For connection of components that have RGB or
component output jacks such as a personal computer,
DVD player, or external RGB decoder. Make sure that
the connection made corresponds to the format of the
signal output from the connected component (pages 9
to 12).
8
Synchronizing signal impedance selector switch
Depending on the connections made at INPUT2, it
may be necessary to set this switch to match the
output impedance of the connected component's
synchronization signal.
When the output impedance of the component's
synchronization signal is below 75 , set this switch
to the 75
position (pages 10, 12).
7 m
(23 feet)
30˚
30˚
Remote
Sensor