Aeotec WallMote Démarrage rapide

Parcourez en ligne ou téléchargez le pdf Démarrage rapide pour {nom_de_la_catégorie} Aeotec WallMote. Aeotec WallMote 3 pages.
Également pour Aeotec WallMote : Manuel de l'utilisateur (8 pages), Manuel de l'utilisateur (9 pages)

Imprimer la page

WallMote.

Aeotec WallMote is an intelligent Z-Wave remote controller that

mounted on a wall. It has 2 touch buttons that you can easily control

the Z-Wave devices in your home network via touching, long pressing

or sliding the button areas.

Its surface has a RGB LED to indicate the button actions also

accompanied by touch beep and vibration.

The WallMote is also a security Z-Wave device and supports Over The

Air (OTA) feature for the products firmware upgrade.

WallMote

Familiarize yourself with your WallMote.

WallMote

Back-Mount plate

View the expanded manual:

Double-Sided tape

http://aeotec.com/support

Micro USB cable

IMPORTANT!

①

This product has been fully tested and certified to work

with Z-Wave by the Z-Wave Alliance. It is crafted using

Z-Wave Plus, the latest device version of Z-Wave.

As such, if the product does not work with your

gateway, please be sure to check with your gateway

manufacturer that they have integrated this device with

③

their gateway for full operation.

Note: When the WallMote is placed on somewhere, keep the glass

button surface upward direction and no other physical surface or

RGB LED

desktop contact with the glass button surface to avoid false triggering

and battery consumption.

Quick start.

Button 1

Button 2

Installing your WallMote.

Selecting a place or wall in your home to affix your WallMote's Back

Mount plate.

Using the Double-sided tap, wipe the two surfaces clean of any oil

Main unit (Front)

or dust with a damp towel. When the surface has completely dried,

peel one side of the tape back and attach it to the corresponding

section on the rear side of the Back Mounting Plate.

Action Button

Magnet

②

Micro USB port

Main unit (Back)

Back-Mount plate

④

Adding your WallMote to your Z-Wave network.

With your mounting plates prepared to hold each component of your

WallMote, it's time to add it to your Z-Wave network.

Let your Z-Wave primary controller/gateway enter into pairing/

inclusion mode.

Take your WallMote near to your primary controller.

Press the Action Button once on your WallMote, the LED will blink

with green color.

If your WallMote has been successfully added to your Z-Wave

network, its green LED will be solid for 2 seconds and then off. If

Advanced.

the adding was unsuccessful and the red LED will be solid for 2

seconds and then off, repeat the above steps.

Send a wake up notification.

In order to send your WallMote new configuration commands from

With your WallMote now working as a part of your smart home, you'll

your Z-Wave controller or gateway, it will need to be woken up.

be able to configure it from your home control software or phone

application. Please refer to your software's user guide for precise

Remove your WallMote unit from its Back Mounting Plate, press and

instructions on configuring the WallMote to your needs.

hold the Action Button for 3 seconds(the buzzer chirp once and the

Attach your WallMote to its Back Mounting plate.

orange LED will be ON) on the back of the WallMote unit and then

release it. This will trigger and send a wake up notification command

With your WallMote added to the Z-Wave network. It's now time to

to your controller/gateway, then your WallMote will wake up for 10

insert the main unit into the corresponding Back Mount plate.

minutes and the orange LED will fast blink while it is awake (if the

Put the main unit in the top-left direction on the Back Mounting, and

WallMote does not receive the Wake Up No More Info from the

then push the WallMote into the Back Mounting Plate, the WallMote

primary Controller).

will be attracted by the magnets on the Back Mount plate, as the

figure below shows.

Removing your WallMote from a Z-Wave network.

Your WallMote can be removed from your Z-Wave network at any

may want your WallMote is a security device that uses secure/

time. You'll need to use your Z-Wave network's main controller/

encrypted message to communicate in Z-wave network, so a security

gateway. To do this, please refer to the part of their respective

enabled controller/gateway is needed for the WallMote to be used as

manuals that tell you how to remove devices from your network.

a security device. You need to press the WallMote's Action Button 2

times within 1 second when your security controller/gateway starts

Put your primary controller into device removal mode.

the network inclusion. The blue LED will be on for 2 seconds and then

Unlock your WallMote from the Back Mount plate and take the

the orange LED will fast blink for 10 minutes (if the WallMote does not

WallMote unit near to your primary controller.

receive the Wake Up No More Info command from primary Controller)

Press the Action Button on your WallMote.

to indicate the inclusion is successful.

If your WallMote is successfully removed from the Z-Wave network,

Advanced Parameter Configurations.

the LED will become a colourful gradient for a few seconds and

then turn off. If the removing was unsuccessful, the red LED will be

Not all gateways will allow you to further configure your Z-Wave

solid for 2 seconds and then turn off, repeat the above steps.

devices, but in the case that your gateway does allow it, the WallMote

has some available parameter configurations that will allow you to

Security or Non-security feature of your WallMote in Z-wave

configure it further to your liking.

network.

Touch beep

Including WallMote as a non-secure device:

This will enable or disable the sound effects when you press or touch

If you want your WallMote as a non-security device in your Z-wave

the sensing area. By default, this is enabled.

network, you just need to press the Action Button once on WallMote

when you use a controller/gateway to add/include it. The green LED

Parameter 1 [1 byte]

will be on for 2 seconds and then the orange LED will fast blink for

0: Disable

10 minutes (if the WallMote does not receive the Wake Up No More

1: Enable

Info command from primary Controller) to indicate the inclusion is

successful.

Note: You can also enable or disable the sound effects via pressing

and holding the Action Button for 12 seconds (the buzzer chirp once

Including WallMote as a secure device:

and the red LED will fast blink) and then release.

In order to take full advantage of all functionality the WallMote, you