Ariston GENUS PREMIUM EVO HP 100 Instructions de conception, d'installation et d'entretien - Page 36
Parcourez en ligne ou téléchargez le pdf Instructions de conception, d'installation et d'entretien pour {nom_de_la_catégorie} Ariston GENUS PREMIUM EVO HP 100. Ariston GENUS PREMIUM EVO HP 100 44 pages. Wall-hung condensing
gas boiler hp
Également pour Ariston GENUS PREMIUM EVO HP 100 : Manuel de l'utilisateur (17 pages), Manuel de l'utilisateur (24 pages), Manuel de l'utilisateur (32 pages)
Imprimer la page
technical area
description
notes
5. 2. 3 Parallel curve shift Zone
2 Off set
To adapt the heating curve to the system requirements,
shift the curve in parallel so that the calculated fl ow
temperature is modifi ed, in addition to the room tempe-
rature.
By accessing the parameter and turning the encoder,
it is possible to shift the curve in a parallel direction.
The shifting value can be read on the display: from -14
to +14 for high-temperature devices, or from -7 to 7 for
low-temperature devices. Each step corresponds to a 1°C
increase/decrease In the fl ow temperature with respect to
the set-point value.
5. 2. 4 Room sensor Infl uence
to calculate the set-
point temperature
- Thermoregulation
enabled-
If setted = 0 the room temperature doesn't infl uence the
calculation of the set-point.
If setted = 20, the room temperature has the maximun
infl uence to calculate the set-point
- only active when the BUS device is connected
5. 2. 5 Maximum Central Heating
Temperature Zone 2
5. 2. 6 Minimum Central Heating
Temperature Zone 2
5. 3 DIAGNOSTICS
5. 3. 4 Heat Request Zone 2
6 ZONE 3 PARAMETER
6. 0 ZONE 3 TEMPERATURE SETTING
6. 0. 2 Fix temperature central
heating
To set only with Fixed Flow Temperaure of
Thermoregulation (see 521)
6. 2 ZONE 3 SETTING
6. 2. 0 Zone 3 Temperature range 0 = from 20 to 45°C
6. 2. 1 Select Type of
Thermoregulation
To enabled
thermoregulation press
Auto button.
36
value
from - 14 to + 14 (°C)
0
(high temperature)
from - 7 to + 7 (°C)
0
(low temperature)
from 0 to 20
20
from 35 to 85 °C
82
(Param. 420 = 1)
from 20 to 45 °C
45
(Param. 420 = 0)
from 35 to 85 °C
40
(Param. 420 = 1)
from 20 to 45 °C
25
(Param. 420 = 0)
0 = OFF
1 = ON
from 35 to 85 (°C)
70
(high temperature)
from 20 to 45 (°C)
25
(low temperature)
1
(low temperature)
1 = from 35 to 85°C
(high temperature)
0 = Fixed Flow
1
Temperature
1 = Basic Thermoreg.
2 = Room sensor
3 = Outdoor Temp.
only
4 = Room sensor +
outdoor Temp.
description
notes
6. 2. 2 Zone 3 Slope
See parameter 422
Only enabled when an outdoor sensor is installed
When an outdoor sensor is used, the boiler calculates the
most suitable delivery temperature, taking into account
the outside temperature and type of system. The type
of curve should be selected in correspondence with the
projected temperature of the system and the nature
of the dispersions present in the structure. For high-
temperature systems, one of the curves depicted below
may be chosen.
6. 2. 3 Parallel curve shift Zone
2 Off set
To adapt the heating curve to the system requirements,
shift the curve in parallel so that the calculated fl ow
temperature is modifi ed, in addition to the room tempe-
rature.
By accessing the parameter and turning the encoder,
it is possible to shift the curve in a parallel direction.
The shifting value can be read on the display: from -14
to +14 for high-temperature devices, or from -7 to 7 for
low-temperature devices. Each step corresponds to a 1°C
increase/decrease In the fl ow temperature with respect to
the set-point value.
6. 2. 4 Room sensor Infl uence
to calculate the set-
point temperature
- Thermoregulation
enabled-
If setted = 0 the room temperature doesn't infl uence the
calculation of the set-point.
If setted = 20, the room temperature has the maximun
infl uence to calculate the set-point
- only active when the BUS device is connected
6. 2. 5 Maximum Central Heating
Temperature Zone 2
6. 2. 6 Minimum Central Heating
Temperature Zone 2
6. 3 DIAGNOSTICS
6. 3. 4 Heat Request Zone 2
8 SERVICE PARAMETERS
8. 1
STATISTICHE
8. 1. 0 Hours Burner On (Central Heating) (XXh)
8. 1. 1 Hours Burner On (Domestic Hot Water) (XXh)
8. 1. 2 Number of Flame Faults
8. 1. 3 Numbeer of ignition Cycles
8. 1. 4 Heat request Duration
value
from 1.0 to 3.5
1.5
(high temperature)
from 0.2 to 0.8
0.6
(low temperature)
from - 14 to + 14 (°C)
0
(high temperature)
from - 7 to + 7 (°C)
0
(low temperature)
from 0 to 20
20
from 35 to 85 °C
82
(Param. 420 = 1)
from 20 to 45 °C
45
(Param. 420 = 0)
from 35 to 85 °C
40
(Param. 420 = 1)
from 20 to 45 °C
25
(Param. 420 = 0)
0 = OFF
1 = ON