Whirlpool 3XLA87W92BQ0 Instructions d'installation - Page 4

Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} Whirlpool 3XLA87W92BQ0. Whirlpool 3XLA87W92BQ0 5 pages.

Imprimer la page

Drain hose

connection:

-..:::::::y

:.:.:.:

. . . . . . ..::

Leveling

washer:

8:....

:j,::::::

::::::::::

jjjjjjjjjj

..::j:j:j:

. . . . . ..:

IMPORTANT:

THIS PROCEDURE MUST

BE FOLLOWED

TO ASSURE PROPER

INSTALLATION.

k: r

. . .

To prevent the drain hose from

coming off or leaking, it must be

jinstalled

per the following

instructions.

Wet the inside end of the drain hose

with tap water. DO NOT USE ANY

OTHER LUBRICANT.

Squeeze ears of one hose clamp with

pliers to open and place clamp over the

end of the drain hose.

Open clamp and push end of drain hose

onto drain connector

until hose contacts

ribbed stop.

Place clamp over area marked "clamp".

Release clamp.

Open small clamp

and slide over

SLIDE WASHER ONTO CARDBOARD

OR HARDBOARD

BEFORE MOVING

ACROSS FLOOR.

"hook" end of drain hos

to secure the rigid and

corrugated

sections

together.

If drain hose does not

fit into standpipe

or is

being placed over the

edge of a laundry tub,

open other hose clamp

with pliers and place

clamp over rigid end of

drain hose.

Insert end of hose

extension into rigid end of drain hose

to stops on the sides of hose extension.

Secure with clamp.

Run water through

both faucets

into a bucket to get rid of

particles in the water lines that might

clog hoses. Mark the hot water faucet.

Move washer close to final

position. Put "hook"

end of drain

hose into laundry tub or standpipe.

Check for proper length of drain hose.

DO NOT FORCE EXCESS LENGTH OF

DRAIN HOSE DOWN THE STANDPIPE.

THIS COULD CAUSE SIPHONING.

CROSSTRREAD.

Attach bottom hose (inlet marked

"H") to hot water faucet. Attach

top hose (inlet marked "C") to cold water

faucet. Adapters may be necessary to

connect the hoses to the faucets.

Tighten couplings to faucets. DO NOT

OVERTIGHTEN;

this could cause

damage to coupler.

Stack two corner posts on top

of each other. Tilt washer

backwards and insert corner posts 7.6 cm

(3 inches) from one side of washer as

shown. Repeat with other corner posts

on other side of washer.

Insert legs into correct holes at each front

corner of washer until nuts touch washer.

DO NOT tighten nuts until Step 15.

Tilt washer forward, raising

back legs 2.5 cm (1 inch) off

of floor to adjust rear self-leveling

legs.

Gently lower washer to floor. Check

levelness of the washer by placing a

carpenter's level on top of the washer,

first side to side; then front to back.

Tilt washer backward and

0 remove corner posts. Gently

lower washer to floor.

Move washer

to Its final

location.

Remove

cardboard

or hardboard

from

under

washer.

Screw nut down on legs to

within 1.3 cm (l/2 inch) of base.

If washer is not level, adjust the

front legs up or down. Repeat Step 14.

When

washer

is level,

use wrench

to turn

nuts on front

legs up

tlghtly

agalnst

washer

base. If nuts

are not tlght

against

washer

base,

the washer

may vibrate.

Securing

drain hose:

Injury

Hazard

Use shipping

strap

to secure

drain

hose. Water

pressure

could

cause drain

hose to come out of

standplpe

or laundry

tub if drain

hose is not secured.

Failure

to secure drain

hose could

result

in injuries

from

slipping

and falling

In water

on floor.

rfter strap has been removed from

yasher (Step l), measure and mark a

joint approximately

38.1 cm (15 inches)

rom the plug end of the shipping strap.

Iut the shipping strap at this point.

Check that

hose is not twisted

kinked

and Is securely

in place.

Push plug into

the nearest hole

in the shipping

strap.

strap

Put "hook"

end of drain hoszin

laundry

tub or standpipe.

Tightly wrap the

shipping strap around the drain hose and

laundry tub or standpipe or inlet hose as

shown in Figures A-B. Push plug into the

nearest hole in the shipping strap.

If the water inlet faucets and drain

standing pipe are recessed, put "hook"

end of drain hose in tub or standpipe.

Tightly wrap the shipping strap around

the drain hose and faucet body (not the

handles or stems) as shown in Figure C.

If a longer drain hose is needed, drain

hose extension kit (Part No. 285702) is

available from authorized

parts

distributors.

If drain hose must be

shortened,

use hose kit (Part No.

285442).

Note: If washer

is moved

to adjust

drain

hose, the washer

must

leveled

again.

Repeat

Steps 14-15.

Place cardboard

under

the washer

and carefully

move washer

avoid

damaging

floor

covering.

Panel C