Whirlpool 4GWTW4740 Manuel d'instructions d'installation - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} Whirlpool 4GWTW4740. Whirlpool 4GWTW4740 27 pages.
Également pour Whirlpool 4GWTW4740 : Manuel d'utilisation et d'entretien (47 pages), Manuel d'instructions d'installation (27 pages), Manuel d'instructions d'installation (27 pages)

Whirlpool 4GWTW4740 Manuel d'instructions d'installation
Alternate
parts:
(Not supplied with washer)
Your installation may require additional parts. To order, please
contact the dealer from whom you purchased your washer or an
authorized service company.
If you have:
Overhead sewer
1" (25 mm) standpipe
You will need:
Standard 20 gal. (76 L) 39" (990 mm)
tall drain tub or utility sink, sump
pump and connectors
(available from
local plumbing suppliers)
2" (51 mm) diameter to 1" (25 mm)
diameter Standpipe Adapter
Part Number 3363920
Connector Kit Part Number 285835
Drain hose too short
Extension Drain Hose Part
Number 285863
Connector Kit Part Number 285835
Lint clogged drain
Drain Protector Part Number 367031
Connector Kit Part Number 285835
LOCATION REQUIREMENTS
Select proper location for your washer to improve performance
and minimize noise and possible "washer walk". Install your
washer in a basement, laundry room, closet, or recessed area.
42"
(1067 mm)
You will need:
[] A water heater set to 120 ° F (49° C).
[] A grounded electrical outlet located within 4 ft (1.2 m) of
power cord on back of washer.
[] Hot and cold water faucets located within 3 ft (0.9 m) of hot
and cold water fill valves on washer, and water pressure
of 20-100 psi (138-690 kPa).
[] A level floor with maximum slope of 1" (25 mm) under entire
washer. Installing on carpet is not recommended.
[] Floor must support washer's total weight (with water and load)
of 315 Ibs (143 kgs).
IMPORTANT:
Do not install, store, or operate washer where it
will be exposed to weather or in temperatures
below 32 ° F (0° C).
Water remaining in washer after use may cause damage in low
temperatures.
See "Washer Care" in your Use and Care Guide
for winterizing information.
Proper installation is your responsibility.
Recessed
area or closet installation
(76 ram)
u
14 =. max.
i
(356 ram) .... j__.
,L,,:,i
Jlq
I
(126 m
, ,,,,
,
\ \t iq
\%q
(25 ram)
117"
(432 ram)
(25 ram)
48 in.2
(310 cm2)
¢3
24 in.2
(155 cm2)
(76 ram)
Dimensions show recommended
spacing allowed, except for
closet door ventilation openings which are minimum required.
This washer has been tested for installation with spacing of
0" (0 mm) clearance on the sides. Consider allowing more space
for ease of installation and servicing, and spacing for companion
appliances and clearances for walls, doors, and floor moldings.
Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or Iouvered door is installed,
top and bottom air openings in door are required.
DRAIN SYSTEM
Drain system can be installed using a floor drain, wall standpipe,
floor standpipe,
or laundry tub. Select method you need.
Floor
standpipe
drain
system
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe
must be at least 39" (990 mm) high; install no higher than
48" (1.22 m) from bottom of washer. If you must install higher
than 48" (1.22 m), you will need a sump pump system.