Whirlpool AMAZONE CO Manuel de référence rapide - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel de référence rapide pour {nom_de_la_catégorie} Whirlpool AMAZONE CO. Whirlpool AMAZONE CO 2 pages.

Imprimer la page

PREPARING THE LAUNDRY

1. Check that all fastenings are closed and that

pockets are empty.

2. Turn the articles inside out.

3. Place laundry loosely in the drum to make

sure it doesn't become tangled.

Sort laundry as follows:

A) By care symbols (on the collar or inside

seam):

Suitable for tumble drying

Tumble drying with reduced drying

intensity only. Press Gentle button.

Do not tumble dry

B) By amount and thickness/weight

Whenever the load to be dried exceeds dryer

capacity, separate laundry according to

weight (e.g. towels from thin underwear).

C) By type of fabrics

Cotton/linen: Towels, cotton jersey, bed and

table linen made of cotton or linen.

Synthetics/Easy Care: Blouses, shirts,

overalls, etc. made of polyester or polyamide,

as well as cotton/synthetic mixes.

D) By drying level

• Sort into: iron dry, cupboard dry, etc.

Do not tumble dry: Woollens, silk, nylon

stockings, delicate embroidery, fabrics with

metallic decorations, bulky items such as

sleeping bags, etc.

Important: only use specific indicated dryer-

safe additives and rinse items that have been

treated with stain remover thoroughly in plenty

of water before drying. Only use specific

indicated dryer-safe plastic items and never

dry rubber or articles contaminated with

vegetable oil in the dryer

SELECTING A PROGRAMME & OPTIONS

Programme and Options:

•

To select a programme, turn the programme

selector knob to the required position. The

drying indicator lamp is blinking, indicating

that the cycle needs to be started.

•

To select an option, press the corresponding

button. The indicator light in the button

lights up confirming that the selection has

been made.

•

Press the option button again to cancel the

option.

STARTING & COMPLETING A PROGRAMME

1. Having selected the desired programme and

options, press the Start/Pause button.

If the laundry is not removed at the end of

the drying cycle, an automatic anti-crease

cycle will operate for maximum 60 min.

The drum rotates at regular intervals,

preventing the laundry from creasing.

2. On completion of the programme, set the

programme selector knob to position "0".

CHANGING A PROGRAMME

When changing the programme during the drying

cycle, the dryer stops. The drying indicator lamp

is blinking.

To operate the new programme, press the

Start/Pause button.

INTERRUPTING A PROGRAMME

To interrupt the dryer during operation

1. Set the programme selector knob to Airing.

2. Press the Start/Pause button.

Wait at least 5 minutes before opening the

door to allow the dryer to cool down.

For your safety the programme stops

automatically if you open the door.

3. To restart, after door opening, close the door

and press the Start/Pause button again.

DAILY MAINTENANCE & CLEANING

Clean the lint filter at the end of every drying

cycle:

1. Open the door.

2. Pull the filter upwards.

3. Open the filter.

4. Remove lint using a soft brush or your fingertips.

5. Close the filter.

6. Push the filter back into place.

Empty the water container at the end of every

drying cycle.

1. Pull the handle to remove the water container.

2. Empty the water container.

3. Replace the water container when empty by

pushing it completely back in place.

TROUBLESHOOTING GUIDE

If a fault occurs, before contacting our After-

Sales Service, make the following checks to try

and remedy the problem:

Drying takes too long / laundry is not dry enough:

•

Was the correct programme selected?

•

Was the inserted laundry too wet (Washing

machine spin speed less than 800 rpm? When

the spinning speed is less than 800 rpm the

water container fault may occur during the

drying cycle.)?

•

Is the lint filter dirty (filter indicator lamp on)?

•

Is the heat exchanger dirty? (refer to the

Instructions for use)

•

Is the ambient temperature too high?

The dryer does not operate:

(after a power failure and/or interruption to

the mains supply, always press the Start/

Pause button).

•

Is the plug properly inserted into the mains

electricity socket?

•

Is there a power failure?

•

Has the fuse blown?

•

Is the door properly closed?

•

Has the programme been selected?

•

Has the Start/Pause button been pressed?

Lint filter or water container indicator lamp

light on:

•

Is the lint filter clean?

•

Is the water container empty?

•

Is the water container correctly positioned?

•

Is the heat exchanger clean?

Water droplets underneath the dryer:

•

Is the heat exchanger correctly positioned?

•

Has any fluff on the heat exchanger seal

been wiped away?

•

Has any fluff on the door seal been wiped away?

•

Has the water container been positioned

correctly?

AFTER-SALES SERVICE

If, after carrying out the above checks the

malfunction persists or appears again, turn the

dryer off and call our After-Sales Service (refer to

guarantee).

Please specify:

•

The nature of the fault.

•

The dryer type and model.

•

The service code (the number after the word

Service on the adhesive rating plate) on the

right-hand side when the door is open.

•

Your full address and phone number.

5019 307 00328