Whirlpool AWE 2117 Manuel - Page 4
Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Whirlpool AWE 2117. Whirlpool AWE 2117 4 pages.
Imprimer la page
CONSUMPTION DATA
Temperature
Programme
(°C)
95
Cotton / Antibacterial
Cotton **
60
Cotton
40
Synthetics
60
Synthetics
40
Delicates
40
Quick wash 30'
30
Wool
40
Handwash
40
Prewash cycle increases programme duration by approximately 20 min. Consumption values were measured in
normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect
to the values in the table in relation to the water supply pressure and temperature, load and type of wash.
*
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump
drains the water out.
**
Reference programme for energy label.
PREPARATION OF THE WASH CYCLE
1. Load the machine, close the drum doors and
check that they are properly locked.
2. Add detergent and additives into the dispenser to
no more than the "MAX" level mark, as follows:
• Programme with pre and main wash
• Main wash programme without prewash
• Fabric softeners and conditioners
• Stain remover agents
• Anti-scale agents (if necessary)
3. Close the lid.
4. Turn the programme selector to the desired
programme and temperature. The lamp next to
the "Start/Pause" button flashes.
Load
Water
Energy
Approx. Programme
Duration
(kg)
(l)
(kWh)
(hours : minutes)
5.0
50*
1.70
2:05
5.0
49
0.95
2:10
5.0
55
0.55
2:00
2.5
50*
0.80
1:30
2.5
45
0.45
1:15
1.5
50
0.55
0:45
3.0
35
0.40
0:30
1.0
55
0.55
0:45
1.0
40
0.40
0:35
SELECT THE DESIRED OPTION(S)
Selecting or deselecting an option can be done
at any time during the programme. The option
will be applied as long as the corresponding
programme phase has not been executed yet.
"Cold Wash" button
• Water is heated only up to 20°C.
• Suitable for delicate laundry items with wash
temperature recommendation of max. 30°C on
the care label.
• Selectable only on the lowest temperature step
of each programme.
"Rinse Hold" button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
"Synthetics" and "Delicates" programmes.
• It is useful if you want to postpone spinning to a
later time, or if you want to drain only.
• If you select "Rinse hold", do not leave items to
soak for too long.
• As soon as the appliance stops in the rinse hold,
the "Rinse hold" lamp of the programme
sequence indicator lights up and the lamp next to
the "Start/Pause" button flashes.
Terminate the "Rinse hold" option:
• Press the "Start/Pause" button; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector to the "Drain" programme
and press the "Start/Pause" button.
PROGRAMME START
Turn on the tap and press the "Start/Pause"
button. The lamp next to the "Start/Pause"
button lights up. The programme sequence
indicator shows the current programme phase,
running from left to right through Wash, Rinse,
Spin/Drain. When the programme phase is
finished, the corresponding indication goes off.
• Note: If there is a power interruption or if the
appliance is disconnected during the cycle, the
programme will run again from the point
where it was interrupted.
"DOOR OPEN" INDICATION
Before starting and after end of a programme, the
lamp lights to show that the lid can be opened. As
long as a wash programme is running, the lid
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to "Cancel
(Reset) a running programme before the end".
RED INDICATIONS
"Service"
Lighting up of the "Service" indication can be caused
by a fault in an electrical component. Refer to the
"Troubleshooting Guide" in your Instructions for Use;
if the fault persists, contact our After Sales Service.
"Water tap closed"
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the "Troubleshooting Guide" in the
Instructions for Use.
"Clean pump"
Waste water is not pumped out. Check whether
the drain hose is kinked or the filter must be
cleaned; in the latter case refer to the Instructions
for Use ("Cleaning the Filter").
PROGRAMME END
All the lights of the programme sequence indicator
are off, and the "Door open" indication lights up.
1. Turn the programme selector to the "Off/O"
position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open for some time to allow the
interior of the machine to dry.
CHANGE PROGRAMME AND/OR
OPTIONS AFTER PROGRAMME START
1. Press the "Start/Pause" button to pause the
programme. The light flashes.
2. Select the new programme, any options and
another spin speed if you want.
3. Press the "Start/Pause" button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
The "Reset" button cancels a programme before
the end. Press the "Reset" button for at least 3
seconds. Any existing water is drained out before
the lid can be opened.
Whirlpool is a registered trademark of Whirlpool USA
5019 312 10573