Ariston PH 941MSTB Manuel d'installation et d'utilisation - Page 19

Parcourez en ligne ou téléchargez le pdf Manuel d'installation et d'utilisation pour {nom_de_la_catégorie} Ariston PH 941MSTB. Ariston PH 941MSTB 34 pages. Built-in cooking table
Également pour Ariston PH 941MSTB : Manuel d'instructions pour l'installation et l'utilisation (13 pages), Manuel d'utilisation (13 pages), Manuel d'utilisation (20 pages)

Imprimer la page

Ariston PH 941MSTB Manuel d'installation et d'utilisation

Hook position for

H=30mm top

Hook position for

H=20mm top

N.B: Use the hook contained in the "accessoires set"

f) In the event the cooktop is not installed above a built-

in oven, a wood panel must be inserted as insulation.

This panel must be placed at least 20 mm from the

bottom of the cooktop itself.

Important: When installing the hob above a built-in oven,

the oven should be placed on two wooden strips; in the

case of a joining cabinet surface, remember to leave a

space of at least 45 x 560 mm at the back.

When installing on a built-in oven without forced ventilation,

ensure that there are air inlets and outlets for ventilating

the interior of the cabinet adequately.

Gas connection for gas hob

The cooker should be connected to the gas-supply by a

corgi registered installer. During installation of this product

it is essential to fit an approved gas tap to isolate the supply

from the appliance for the convenience of any subsequent

removal or servicing. Connection of the appliance to the

gas mains or liquid gas must be carried out according to

the prescribed regulation in force, and only after it is

Hook position for

H=40mm top

Front

Back

ascertained that it is adaptable to the type of gas to be

used. If not, follow the instructions indicated in the

paragraph headed "Adaptation to different gas types". In

the case of connection to liquid gas, by tank, use pressure

regulators that conform to the regulation in force.

Important: For safety, for the correct regulation of gas use

and long life of the appliance, ensure that the gas pressure

conforms to the indications given in table 1 "Nozzle and

burner characteristics".

Connection to non-flexible tube

(copper or steel)

Connection to the gas source must be done in such a way

as to not create any stress points at any part of the

appliance.

The appliance is fitted with an adjustable, "L" shaped

connector and a gasket for the attachment to the gas supply.

Should this connector have to be turned, the gasket must be

replaced (supplied with the appliance).

The feeding connector of the gas to the appliance is

threaded 1/2 gas male cylinder.

Connection to flexible steel tube

The gas feed connector to the appliance is a threaded,

male 1/2" connector for round gas pipe. Only use pipes

and sealing gaskets that that conform to the standards

currently in force. The maximum length of the flexible pipes

must not exceed 2000 mm. Once the connection has been

made, ensure that the flexible metal tube does not touch

any moving parts and is not crushed.

Check the Seal

Once the appliance has been installed, make sure all the

connections are properly sealed, using a soapy water

solution. Never use a flame.

Electrical Connection

The cooktops fitted with a tripolar electrical supply cord

are designed to be be used with alternating current

according to the indications on the rating plate located

under the cooktop. The earthing wire can be identified by

its yellow-green colour.

In the case of installation over a built-in electric oven,

the electrical connections for the cooktop and oven

should be independent, not only for safety purposes, but

also to facilitate removal of one or both in the future.

Electrical Connection for Gas Cooktop

Fit the supply cord with a standard plug for the demand

rate indicated on the rating plate or connect it directly to

the electrical mains. In the latter case, a single pole switch

must be placed between the appliance and the mains,

with a minimum opening between the contacts of 3 mm in

compliance with current safety codes (the earthing wire

must not be interrupted by the switch). The power supply

cord must be positioned so that it does not reach a tem-

perature in excess of 50°C above room temperature at

any point.

Before actual connection make sure that:

•

The fuse and electrical system can withstand the load

required by the appliance;

•

That the electrical supply system is equiped with an

efficient earth hook-up according to the norms and

regulations prescribed by law;