Whirlpool WED9051YW Manuel d'utilisation et d'entretien - Page 7

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation et d'entretien pour {nom_de_la_catégorie} Whirlpool WED9051YW. Whirlpool WED9051YW 20 pages. Installation guide
Également pour Whirlpool WED9051YW : Manuel d'instructions d'installation (20 pages)

Imprimer la page

For direct-wired dryers:

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Disconnect wiring.

3. Make sure leveling legs are secure in dryer base.

4. Use masking tape to secure dryer door.

Reinstalling the dryer

Follow the "Installation Instructions" to locate, level, and connect

the dryer.

First try the solutions suggested here and possibly avoid the cost of a service call...

Dryer Operation

Dryer will not run

■

Is the dryer door firmly closed?

■

Was the START/PAUSE button firmly pressed?

Large loads may require pressing and holding the Start/Pause

button for 2-5 seconds.

■

Has a household fuse blown, or has a circuit breaker

tripped?

There may be 2 household fuses or circuit breakers for the

dryer. Check that both fuses are intact and tight, or that both

circuit breakers have not tripped. Replace the fuse or reset the

circuit breaker. If the problem continues, call an electrician.

■

Is the correct power supply available?

Electric dryers require 240-volt power supply. Check with a

qualified electrician.

■

Was a regular fuse used?

Use a time-delay fuse.

Unusual sounds

■

Has the dryer had a period of non-use?

If the dryer hasn't been used for a while, there may be a

thumping sound during the first few minutes of operation.

■

Is a coin, button, or paper clip caught between the drum

and front or rear of the dryer?

Check the front and rear edges of the drum for small objects.

Clean out pockets before laundering.

■

Are the four legs installed, and is the dryer level front to

back and side to side?

The dryer may vibrate if not properly installed. See the

Installation Instructions.

TROUBLESHOOTING

For additional recommendations, refer to your Installation Instructions.

Changing the Drum Light

The dryer light automatically turns on inside the dryer drum when

you open the door.

To change the drum light:

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the back

wall of the dryer. Remove the screw located in the lower right

corner of the cover. Remove the cover.

3. Turn bulb counterclockwise. Replace the bulb with a 10-watt

appliance bulb only. Replace the cover and secure with the

screw.

4. Plug in dryer or reconnect power.

■

Is the clothing knotted or balled up?

When balled up, the load will bounce, causing the dryer to

vibrate. Separate the load items and restart the dryer.

No heat

■

Has a household fuse blown, or has a circuit breaker

tripped?

The drum may be turning, but you may not have heat. Electric

dryers use 2 household fuses or circuit breakers. Replace the

fuse or reset the circuit breaker. If the problem continues, call

an electrician.

Dryer displaying error message (WET indicator flashing)

WET indicator is flashing:

If the WET indicator on the dryer control panel is flashing, with

a pause between flashes, the dryer control has detected a

problem that requires service. Call for service.

Dryer Results

Clothes are not drying satisfactorily, drying times are too

long, or load is too hot

■

Is the lint screen clogged with lint?

Lint screen should be cleaned before each load.

■

Has the Air Dry temperature setting been selected?

Select the right temperature for the types of garments being

dried. See "Additional Features."

■

Is the load too large and heavy to dry quickly?

Separate the load to tumble freely.