Before
you
start...
Read
Eleclriccrl
and
Carpenhy
instructions.
Proper installation is your responsibility. A
qualified technician
should install this oven.
Make sure You have everyMing
necessary
for correct installation. lt Is the resgotibilitv
of
the installer to comply with the in&all~on'
clearances
specifed
on the serial/ratina elate
The serial/rating plate is located dehing&e
Oven door on
the front
frame.
Check
location where oven till be installed
Cabinel
opening
dimensions
that
are shown
must
be
used Given dimensions provide minimum clearance.
Contact
surface must be solid and level.
The
recessed
inslallaiion
area
must provide complete
enclosure around me recess&
portion of the oven.
AU OPENINGS 1~ THE WALL OR FLOOR WHERE OVEN
tS TO BE INSTALLED MUST BE SEALED.
Remove
all
packaging
material from microwave
oven cavity
Check mlcrowave
Oven area for
damage-
see WARNING below. If any damage
is
evident, do not ooerate until microwave
oven is
The location should be away horn strong draft
area. such as windows. doors, and strong
Testing vents or fa M-S The oven should be
Notated for conver lient use in the Ltifchen.
checked
by an duthorized service technician.
"Note: hrm In",,
Clearances
specified
are for
combusfible
walls
and
malerials
that
have
a density
of 20 or more
pounds
per cubic
1001. No evaluation
of
clearances
has been
made
for
insfallalions
adjacent
fo malerials
fhol
Elechicol
ground
is required
See Electrical requirements.
Blocking
lhe oven
venl
may
touse
cabinet
damage
and
mr
baking
flush
wilh
the bottom
of fhe cabinet
Tools needed for
installation:
Electrical
requirements
A
Thb appliance
must be
. connected
to
me
otooer
electrical voltage and f&&cy
as
spechied on the serial/rating plate.
Models rated at 7.0 kxv on 240 volts (5.3
kw on x)8 v&s) or mbre require 0
separate 4O-ampere circuit. Models
rated at 3.6 hv on 240 vdts (2.7 kw on
208 volts) or les require a separate 30
ampere circuit Fuse both sides of me
line. A timedelay
fuse or circuit
breaker ls recommended.
B ovm
MUST BE CONNECTED WITH
. COPPER WIRE ONLY.
Parts provided
for installation:
Personal
Injury
Hazard
* Do Nol aHerr@
lo operale
Ihe
n+crowave
oven
wilh
Ihe door
open.
l
Do Nd
tamper
wilh
or defeoi
Ihe
safev
inferlocks.
- Do Nd
place
objects
between
Ihe
ticrowave
oven
front face
and
door.
- Do Nd
allow
soil or cleaner
residue
lo accumulate
on sealing
surface
of
the microwave
oven
door.
l
Do Nol operale
the Wcrowave
oven
il CkJrMged.
- Do Nof operate
Ihe mfcrowove
oven
5 door
is bent
-hinges
and
latches
are broken
or
kxse.
-
dca
seals,
sealing
surfaces
or
glass
are broken.
The microwave
oven
door
must
close
properly
lo provide
safe operation.
- Only
have
a qualified
repair
person
adjust.
repair
and
check
microwave
oven
for microwave
leakage
cn?er a
repair
ts made.
- Do No! use microwave
for
commercial
purposes.
The
mfcrowove
oven
In lhis unit is
designed
for household
use c+.
Failure
10 follow
these
instructions
could
resutl
In exposure
lo excessive
microwave
energy.
Elechicol
Shock
Hazard
* Electrical ground is required on this
appliance.
- Improper
conneciion
of the
equipmenl-grounding
conductor
line
con
resuil
in a risk of elechicol
shock.
- Check
with
o quafiied
electrician
il you
ore in doubt
as lo whether
Ihe appliance
ir property
grounded.
- Do Nol hove
a fuse in Ihe neulrol
or
grounding
circuit.
A fuse in Ihe
neuirol
or groundinq
circuit
could
resufl
in el&hicof
shock.
Failure
lo follow
these
instructions
could
result
in o Bre, elecfrical
shock
or other
personal
injury.
Save
lnstollalion
lnshucfions
for
elechicaf
inspeclofs
use.
Elechical
Shock
Hazard
II is Ihe customer's
responsibilii:
l
To contacl
a quolired
electrical
insloller.
- To assure
that Ihe eleclrical
inslallallon
is odequale
and
in
conformance
wth
Naiional
Electrical
Code.
ANWNFPA
70-lalesl
edfiion.'
and
all local
codes
and
ordinances.
Failure
to fdiow
Ihere
inshuctiis
could
resuli
in elechical
shock.
Pencix~l
Injury
Hazard
* Securely
fasten
oven
to cabinet
using
Ihe hvo screws
provided.
Failure
lo do so could
cause
oven
lo
mve
or lip during
use and
resuli
in
personal
Injury.
-
C
wire sizes and connections
. must conform to me
requirements of the National Electrical
Code ANSI/NFPA 70 - Ikrtest edition'
and all local codes and ordinances
for the kilowatt rating of the oven
This rating can be found on the
serial/rating plate located behind the
oven door on the front frame.
D
This appliance
should be
n
connected
dire&
to the
fused disconnect
(or circuit breaker)
through flexible, armored or non-
metallic sheathed. copper cable (with
Panel
A
Imprimer la page