Whirlpool AWZ 2413 Manuel de référence rapide - Page 2
Parcourez en ligne ou téléchargez le pdf Manuel de référence rapide pour {nom_de_la_catégorie} Whirlpool AWZ 2413. Whirlpool AWZ 2413 2 pages.
Imprimer la page
PREPARING THE LAUNDRY
1. Check that all fastenings are closed and that
pockets are empty.
2. Turn the articles inside out.
3. Place laundry loosely in the drum to make
sure it doesn't become tangled.
Sort laundry as follows:
A) By care symbols (on the collar or inside
seam):
Suitable for tumble drying
Tumble drying with reduced drying
intensity only. Press Gentle button.
Do not tumble dry
B) By amount and thickness/weight
Whenever the load to be dried exceeds dryer
capacity, separate laundry according to
weight (e.g. towels from thin underwear).
C) By type of fabrics
Cotton/linen: Towels, cotton jersey, bed and
table linen made of cotton or linen.
Synthetics/Easy Care: blouses, shirts, overalls,
etc. made of polyester or polyamide, as well as
cotton/synthetic mixes.
D) By drying level
• Sort into: iron dry, cupboard dry, etc.
Do not tumble dry: woollens, silk, nylon
stockings, delicate embroidery, fabrics with
metallic decorations, bulky items such as
sleeping bags, etc.
Important: only use specific indicated dryer-
safe additives and rinse items that have been
treated with stain remover thoroughly in plenty
of water before drying. Only use specific
indicated dryer-safe plastic items and never
dry rubber or articles contaminated with
vegetable oil in the dryer
.
SELECTING A PROGRAMME & OPTIONS
Programme and Options:
•
To select a programme, turn the programme
selector knob to the required position. The
drying indicator lamp is blinking "
",
indicating that the cycle needs to be started.
•
To select an option, press the corresponding
button. The indicator light in the button
lights up confirming that the selection has
been made.
•
Press the option button again to cancel the
option.
STARTING & COMPLETING A PROGRAMME
1. Having selected the desired programme and
options, press the Start/Pause button.
If the laundry is not removed at the end of
the drying cycle, an automatic anti-crease
cycle will operate for maximum 60 min. The
drum rotates at regular intervals, preventing
the laundry from creasing.
On completion of the programme, set the
2.
programme selector knob to position "0".
CHANGING A PROGRAMME
When changing the programme during the drying
cycle, the dryer stops. The drying indicator lamp
is blinking "
".
To operate the new programme, press the
Start/Pause button.
INTERRUPTING A PROGRAMME
To interrupt the dryer during operation
1. Set the programme selector knob to
Airing "
".
2. Press the Start/Pause button.
Wait at least 5 minutes before opening the
door to allow the dryer to cool down.
For your safety the programme stops
automatically if you open the door.
To restart, after door opening, close the door
3.
and press the Start/Pause button again.
DAILY MAINTENANCE & CLEANING
Clean the lint filter at the end of every drying
cycle:
1. Open the door.
2. Pull the filter upwards.
3. Open the filter.
4. Remove lint using a soft brush or your fingertips.
5. Close the filter.
6. Push the filter back into place.
TROUBLESHOOTING GUIDE
If a fault occurs, before contacting our
After-Sales Service, make the following
checks to try and remedy the problem:
Drying takes too long / laundry is not dry
enough:
•
Was the correct programme selected?
•
Was the inserted laundry too wet (Washing
machine spin speed less than 800 rpm)?
•
Is the lint filter dirty (filter indicator lamp on)?
The dryer does not operate:
(after a power failure and/or interruption to
the mains supply, always press the Start/
Pause button).
•
Is the plug properly inserted into the mains
electricity socket?
•
Is there a power failure?
•
Has the fuse blown?
•
Is the door properly closed?
•
Has the programme been selected?
•
Has the Start/Pause button been pressed?
Lint filter indicator lamp light on:
•
Is the lint filter clean?
•
Is the vent hose blocked?
All programme sequence indicators blinking:
•
Service call necessary
AFTER-SALES SERVICE
If, after carrying out the above checks the
malfunction persists or appears again, turn the
dryer off and call our After-Sales Service (refer to
guarantee).
Please specify:
•
The nature of the fault.
•
The dryer type and model.
•
The service code (the number after the word
Service on the adhesive rating plate) on the
right-hand side when the door is open.
•
Your full address and phone number.
5019 307 00297