Whirlpool Electric and Gas Dryers Manuel d'instructions d'installation - Page 3
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} Whirlpool Electric and Gas Dryers. Whirlpool Electric and Gas Dryers 8 pages. Commercial dryers
Également pour Whirlpool Electric and Gas Dryers : Manuel d'utilisation et d'entretien (33 pages), Manuel d'utilisation et d'entretien (28 pages), Manuel d'utilisation et d'entretien (21 pages), Manuel d'utilisation et d'entretien (31 pages)
Imprimer la page
GAS DRYER MODELS
J-PRONG
\
3-PRONG
GROUNDING
PLUG
POWER SUPPLY
CORD
FIGURE 3
J-PRONG
GROUNDING
TYPE
WALL RECEPTACLE
ALTERNATE
GROUNDING
METHOD
DO NOT,
UNDER
ANY
CIRCUMSTANCES,
REMOVE
THE
POWER SUPPLY CORD GROUND
PRONG.
If changing
and
properly
grounding
the wall
receptacle,
is impossible
and where
local
codes
permit
(consult
your electrical
inspector),
a tem-
porary
adapter
may be plugged
into the existing
2-prong
wall receptacle
to mate with the 3-prong
power
supply
cord.
THIS, HOWEVER,
IS NOT
RECOMMENDED.
If this is done, you must connect
a separate copper
ground
wire (No. 18 minimum)
to a grounded
cold
water pipe* by means of a clamp and then to the
external
ground
connector
screw. See Figure 4. Do
not ground
to a gas supply pipe. Do not connect
to
electrical
supply
until
appliance
is permanently
grounded.
*Grounded
cold
water
pipe must have metal
continuity
to electrical
ground
and
not
be interrupted
by plastic,
rubber
or electrically
insulating
connectors
(including
water
meter
or pump)
without
adding
a jumper
wire at these connections.
INSTALLATION
PROCEDURE
1.
Open the dryer door and remove the shipping
tape that holds the d'rum to. the cabinet.
2. Remove
all
literature
and
installation
parts
from-the
dryer drum.
3. Block up the front of the appliance
about four
inches and install leveling
feet in the front corners.
These feet should
extend
approximately
one inch.
Remove
the block
and repeat
the procedure
at
rear of appliance.
4. Refer to Exhaust
System Requirements
in these
instructions.
-r
5. Move the appliance
to desired location.
Observe
the minimum
clearance
to sides
and
rear as
specified
on the label found on back panel of the
dryer.
To open the toe panel use a putty knife, press on
the toe panel lock located
at the center top of the
toe panel. Pull downward
on the toe panel to open.
The toe panel is hinged at the bottom. See figure 5.
TOE PANEL
-
I
FIGURE 5
6. Level the appliance
from side to side and from
front to rear by adjusting
the leveling
feet. A small
spirit level placed on the dryer top is recommended
for leveling.
7. Connect
the appliance
to the gas supply.
Make
sure the shut-off
valve located behind the toe plate
is open (See Figure 6) and open shut-off
valves in
the supply
line. Test all gas connections
for leaks,
using a brush
and soapy water solution.
(Liquid
detergent
works
very
well
also.)
Bubbles
will
indicate
a loose connection.
NEVER TEST FOR GAS LEAKS WITH A FLAME.
120 VOLT
3.PRONG
RECEPTACLE
I15 AMPI
GAS SHUT-OFF
VALVE
(OPEN1
l/2
INCH
GAS PIPE
13/B INCH
APPROVED
COPPER
TUBING
MAY
BE USED
ON LP GASI
FIGURE 6