Whirlpool YCEM2760TQ0 Manuel d'instructions d'installation - Page 7
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} Whirlpool YCEM2760TQ0. Whirlpool YCEM2760TQ0 36 pages. Commercial gas or electric dryer
Imprimer la pageRecommended G roundMethod
[] InU.S.: Itisyour r esponsibility
tocontact a qualified electrical
installer toensure thattheelectrical installation isadequate
andinconformance
withtheNational ElectricaI Code,
ANSI/NFPA
70,latest edition, andalllocal c odes a nd
ordinances.
[] InCanada: Itisyourresponsibility
toinstall thedryer i n
accordance
withCanadian Electrica! Code, CSA C22.1
installation
codes a nd allnational orlocal codes.
Canadian models areequipped withafour-wire, 30-amp r ated
flexible-type
power c ord. The power cord must b eplugged
intoamating 3 0-amp r eceptacle.
GROUNDING
INSTRUCTIONS
_' For a grounded, cord-connected
dryer:
This dryer must be grounded. In the event of a malfunction or
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer uses a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
_' For a permanently connected dryer:
This dryer must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding
terminal or lead on
the dryer.
WARNING:
Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative or
personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug on the power
supply cord: if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
SAVE THESE
INSTRUCTIONS
Expmosion Hazard
Use a new CSA International
approved
gas suppmy mineo
_nstaH a shut-off
vamve,
Securely
tighten
aH gas connections.
ff connected
to LP, have a quaBified person make sure
gas pressure
does not exceed 14" (36 cm) water
column,
Examp{es of a qualified
person incmude:
micensed heating
personnel,
authorized
gas company
personnem, and
authorized
service
personnel
Failure to do so can resumt in death, expmosion, or fire.
IMPORTANT: Observe all governing codes and ordinances.
This insta!lation must conform with all local codes and
ordinances. In the absence of local codes, installation must
conform with American Nationa! Standard, National Fuel Gas
Code ANSI Z223.1/NFPA 54 or CAN/CSA B149.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch
Park, Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
The design of this dryer has been certified by CSA International
for use at altitudes up to 10,000 feet (3048 m) above sea leveI at
the B.T.U. rating indicated on the model/serial plate. Burner input
adjustments are not required when the dryer is operated up to
this elevation.
When installed above 10,000 feet (3048 m), a four percent (4%)
reduction of the burner B.T.U. rating shown on the mode!/serial
plate is required for each 1,000 foot (305 m) increase in elevation.
For assistance when converting to other gas types and/or
installing above 10,000 feet (3048 m) elevation, contact your local
service company.
Type of Gas
This dryer is equipped for use with natural gas. It is design-
certified by CSA International for LP (propane and butane) gases
with appropriate conversion. No attempt shal! be made to convert
the dryer from the gas specified on the serial/rating plate for use
with a different gas without consuIting the serving gas supplier.
Conversion must be done by a qualified service technician. Gas
conversion kit part numbers are listed on the gas valve burner
base.