AER amp one Manuel de l'utilisateur - Page 10
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} AER amp one. AER amp one 12 pages. Aer bottom-line series amp one user manual
Imprimer la page
Technical data
6. Technical Data
Inputs (notes 1, 4)
input
High-impedance instrument input
Mono jack, ¼" (6.35 mm)
Sensitivity: 21 mV (-34 dBV)
Impedance: 1 Megohm
Equivalent input noise:
1.4 μV (–117 dBV), A-weighted
high / low switch: 10 dB attenuation
clip indicator: 8 dB headroom
aux in
Stereo jack, ¼ " (6.35 mm)
L + R mixed and added pre master, but
after tone controls.
Level control.
Sensitivity: 2 x 170 mV (–15 dBV)
Impedance: 22 k (each channel)
return
Return for external, parallel effect loop
Mono jack socket, ¼" (6.35 mm)
Sensitivity: 360 mV (–9 dBV)
Impedance: 10 k
Outputs (note 2)
headphones
Headphones output. When connected,
internal speaker is muted.
Stereo jack, ¼" (6.35 mm)
Output power: max. 100 mW into 32 ohms
Input sensitivity for 2 x 50 mW / 32 ohms:
25 mV (–32 dBV) at instrument input
For stereo headphones only. Connecting
mono plugs causes overload and may
damage the amp.
line out
Preamp output, post master (note 6)
Mono jack, ¼" (6.35 mm)
Output voltage: 1.9 V (+6 dBV)
sub out
Subwoofer output without filter
Mono jack, ¼" (6.35 mm)
Output voltage: 1.9 V (+6 dBV)
send
Send for parallel effect loop
Mono jack, ¼" (6.35 mm)
Output voltage: 760 mV (–2 dBV)
tuner
Tuner output, not affected by mute
Mono jack, ¼" (6.35 mm)
Output voltage: 800 mV (–2 dBV)
DI out
Balanced XLR output, pre-master,
switchable pre or post tone controls /
effect / aux (note 6).
Output voltage (adjustable): 33...330 mV (–
30 dBV ... –10 dBV)
Insert points
insert pre eq
Insert loop before tone controls and
compressor
Stereo jack, ¼" (6.35 mm)
Output voltage: 800 mV (–2 dBV)
tip = send, ring = return
insert post eq
Insert loop after tone controls
Stereo jack, ¼" (6.35 mm)
Output voltage: 760 mV (–2 dBV)
tip = send, ring = return
Footswitch connections
footswitch
Stereo jack, ¼" for dual footswitch
tip = switch for input muting
ring = on/off switch for external effect
loop (send and return)
sleeve = common (ground)
mute switch disabled when footswitch is
plugged in
Tone controls
colour
–1 dB at 360 Hz, +14 dB at 3.8 kHz
9 dB at 80 Hz
bass
bass boost
+10 dB at 55 Hz
15 dB at 200...2000 Hz (adjustable)
middle
Bandwidth (switchable, note 3):
wide: 1.6 octaves
narrow: 0.6 octaves
treble
12 dB at 6 kHz
www.aer-amps.com
amp one - 2012_01_GB
10
tone balance
Flat if intensity is set fully anticlockwise.
The following values apply if intensity is
set fully clockwise:
balance left:
+12 dB at 50 Hz
balance center:
+9 dB at 50 Hz, and
+10 dB at 10 kHz
balance right:
–2 dB at 50 Hz, and
+11 dB at 10 kHz
(shelf-type frequency response)
Compressor (note 5)
Characteristics
Soft-knee, RMS-responding, gain reduction
Threshold
0.25 mV...78 mV (–72 dBV ... –22 dBV) at
adjustment range
instrument input
Ratio adjustment
1 : 1 ... 5 : 1
range
RMS Time
40 ms
constant
Indicator LED
Lights up at ca. 1 dB gain reduction.
Power
Power amp
200 W / 8 ohms, discrete bipolar transistor
output. Dynamic range, A-weighted: 102
dB (note 4)
Limiter threshold
160 W
Analog signal
Subsonic filter, low distortion RMS limiter
processing
Speaker system
10" (250 mm) woofer, bass reflex enclosure
Mains power
Mains voltage (depending on model): 100,
120, 230, or 240 V AC, 50–60 Hz
Power consumption: max. 500 W
Mains fuse
5 x 20 mm
slow 3.15 A for 230 and 240 V models
slow 6.3 A for 100 and 120 V models
General
Cabinet
15 mm (0.59") birch plywood
Finish
waterbased acrylic, black spatter finish
Dimensions
325 mm (12.8") high
375 mm (14.8") wide
295 mm (11.6") deep
Weight
13.5 kg (29.8 lbs)
Notes:
1. Input sensitivities refer to 160 watts into 8 ohms at full gain and
volume settings, neutral tone control settings (intensity fully
anticlockwise), and 1 kHz sine-wave test signal.
2. Output levels refer to –25dBV (56.2 mV) / 1 kHz at instrument
input, unless stated otherwise.
Earlier models have a DI out adjustable down to zero.
3. Bandwidth of tone controls refers to one-half of gain at center
frequency, in decibels. For example, if a tone control has 15 dB
center gain, then bandwidth refers to the 7.5 dB points.
4. Equivalent input noise voltage obtained by measuring noise
voltage at speaker output and dividing by the voltage gain of the
amplifier for white noise. Full gain and volume settings, neutral
tone control settings, input shorted, frequency range 20 Hz – 20
kHz.
Dynamic range of power amplifier is defined as ratio of output
voltage at limiter threshold to A-weighted noise voltage at master
volume in zero position.
5. Compressor threshold refers to 1 dB gain reduction and input gain
fully clockwise, ratio refers to 20 dB gain reduction. Ratio varies with
gain reduction due to soft-knee compression.
6. If required, aux in and return signals can be disconnected from DI
out by an internal jumper even in the post switch position.
line out can be made master-independent by an internal jumper.
Specifications and appearance subject to change without notice.
TD20110627