Whirlpool 30 " Eye-Level Gas Range Instructions d'installation et manuel d'utilisation et d'entretien - Page 4

Imprimer la page

Product Dimensions

(5.1 cm)

4¹⁵⁄₁₆"

⁷⁄₈"

(12.5 cm)

(2.2 cm)

29¹⁵⁄₁₆" (76.0 cm) or

35¹⁵⁄₁₆" (91.0 cm)

Installation Clearances

A. 24" (61.0 cm) minimum distance from electric cooking surface.

24" (61.0 cm) minimum distance from gas cooking surface.

30" (76.2 cm) suggested maximum above the cooking surface.

B. 18" (45.7 cm) minimum clearance - upper cabinet to countertop.

C. 30" (76.2 cm) minimum cabinet opening width for 30" (76.2 cm)

models and 36" (91.4 cm) minimum cabinet width for 36"

(91.4 cm) models.

D. 12" (30.5 cm) cabinet depth.

E. 36" (91.4 cm) base cabinet height.

6⁹⁄₁₆" (16.7 cm) or

9⁹⁄₁₆" (24.4 cm)

(22.9 cm)

1¹⁄₂"

18⁵⁄₈"

(3.8 cm)

(47.3 cm)

Venting Methods

NOTES:

Flexible vent is not recommended. Flexible vent creates both

back pressure and air turbulence that greatly reduce

(2.5 cm)

performance.

The vent system is optional for this model.

Vent system can terminate either through the roof or wall. Use

3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular with a maximum vent

length of 35 ft (10.7 m) or 7" (17.8 cm) or larger round vent with a

maximum length of 50 ft (15.2 m) for vent system.

Top Venting

A. 7" (17.8 cm) round vent

through roof

(purchased separately).

3¹⁄₄" x 10" (8.3 x 25.4 cm)

rectangular vent through the

roof (purchased separately).

B. Roof cap with damper

(purchased separately)

Cold Weather Installations

An additional back draft damper should be installed to minimize

backward cold air flow and a thermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup Air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Venting Requirements

Vent system must terminate to the outdoors, except for non-

vented (recirculating) installations.

Do not terminate the vent system in an attic or other enclosed

area.

Do not use a 4" (10.2 cm) laundry-type wall cap.

Use 7" (17.8 cm) round metal vent or 3¹⁄₄" x 10" (8.3 x

25.4 cm) rectangular metal vent, depending on your

installation requirement. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

Venting System

Wall Venting

A. 7" (17.8 cm) round vent out

the top and through the wall

(purchased separately).

3¹⁄₄" x 10" (8.3 x 25.4 cm)

rectangular vent through the

wall or out the top (purchased

separately).

B. Wall cap with damper

(purchased separately)