Whirlpool 30 " Eye-Level Gas Range Manuel d'instructions d'installation - Page 13

Imprimer la page

6. For models KEBK171B, KEBK101B, KEBK276B, KEBK206B,

KEBS179B, KEBS109B, KEBS277B, KEBS279B, KEBS207B,

or KEBS209B, see the following instructions.

For all other models, the black front trims can be ordered as

an accessory. Please reference the "Assistance or Service"

section of the Use and Care Guide or contact the dealer from

whom you purchased your built-in oven to order part

numbers:

W10327368 and W10327369 for double ovens.

W10327380 and W10327381 for single ovens.

Remove the tape from black front trims.

Securely fasten the oven to the cabinet using the #8-14 x

¾" screws provided.

Insert the screws through hole in black trim aligning with

hole in oven frame. Do not overtighten screws.

A. Oven frame

B. Oven frame hole

C. Black trim piece

7. The bottom vent and bottom vent trim (required when the

oven is installed with the feet in the tall position) are shipped

in the foam packing at the top of the oven.

To install only the bottom vent, see the following instructions.

To install both the bottom vent and the bottom vent trim for

installations with the feet in the tall position, see the

instructions in Step 8.

Align vent tab (B) with oven frame (A) as shown.

Using one #8-18 x ³⁄₈" screw (D) on each side of the vent

tab (B), fasten the vent securely to the oven.

A. Oven frame

B. Vent tab

C. Oven vent

³⁄₈

D. #8-18 x

" screws

8. On models with the feet installed in the tall position, the

bottom vent trim must also be installed. See the following

instructions to install.

Flex the upper vent piece (C) away from the lower vent

piece (D) to slide the bottom vent trim (B) between them.

Some force may be required to flex the upper vent trim (C)

away from the lower vent trim (D). Some force may also

be required to flex the bottom vent trim (B) and slide it

into position. Make sure screw holes are properly aligned

between the two pieces. See the following illustration.

Install the bottom vent trim (B) to the lower vent piece (D)

¹⁄₄

using two #8-18 x

NOTE: On 27" (68.6 cm) models, only one #8-18 x

used on each side.

¹⁄₄

A. #8-18 x

" screw

B. Bottom vent trim

Align vent tab (B) with oven frame (A) as shown.

Using one #8-18 x ³⁄₈" screw (E) on each side of the vent

tab (B), fasten the vent securely to the oven.

A. Oven frame

B. Vent tab

C. Oven vent

9. Replace the oven racks.

10. Replace the oven door. See the "Replace Oven Door(s)"

section.

11. Check that the door is free to open and close. If it is not,

repeat the removal and installation procedures. See the

"Prepare Built-In Oven" section.

12. Repeat for lower oven door.

13. Reconnect power.

14. The display panel will light briefly, and "PF" should appear in

the display.

15. If the display panel does not light, reference the "Assistance

or Service" section of the Use and Care Guide or contact the

dealer from whom you purchased your oven.

" screws on each side.

¹⁄₄

" screw is

C. Upper vent piece

D. Lower vent piece

D. Bottom vent trim

³⁄₈

E. #8-18 x

" screw