Whirlpool 626701 Manuel d'instructions d'installation - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} Whirlpool 626701. Whirlpool 626701 7 pages.

Imprimer la page

Before you start...

Check the location where the range hood

will be installed. The location should be

Proper installation is your responsibility.

Make sure you have everything

necessary

for correct installation. It is the responsibility

of the installer to comply with the

clearances

specified.

away from strong draft areas, such as

windows, doors, and strong heating vents.

30" model:

29-718

36' model:

35-718"

knockout

for

rear of hood

knockout

for

back vent

mounting

holes

Grounded electric

1 -&w

outlet is required.

See "Electrical

wiring

knockouts

requirements, fl

Electrical Shock Hazard

It is the customer's responsibility:

To contact a qualified electrical

installer.

To assure that the electrical

installation

is adequate

and in conformance

with

National Electrical Code, ANSVNFPA

70 - latest edition*, and all local codes

and ordinances.

Failure to do so could result in fire,

electrical shock or other personal injury.

Care must be taken when drilling

holes into wall. Electrical wires may

be concealed

behind the wall

covering.

Failure to do so could result in electrical

shock or other personal injury.

Personal Injury Hazard

Reaching over a heated cooking

surface should be avoided. To

reduce the hazard of being burned,

the range hood should extend a

minimum of 5 inches out from the

bottom of the cabinet.

Reaching over a heated cooking surface

zould result in a serious burn.

Important: Observe all

governing codes and

ordinances.

Tools and materials

needed for

installation:

compass

or 7"

circle

template

(not shown)

Mobile home installation

The installation of this range hood must

conform to the Manufactured

Home

Construction

Safety Standards, Title 24 CFR,

Part 3280 (formerly the Federal Standard for

Mobile Home Construction

and Safety, Title

24, HUD, Part 280) or when such standard is

not applicable,

the Standard for

Manufactured

Home Installation 1982

(Manufactured

Home Sites, Communities

and Setups) ANSI A225, 1 - 1987, or latest

edition, or with local codes.

Four-wire power supply must be used and

the appliance

wiring must be revised. See

"Electrical requirements."

Copies of standards listed may be obtained

from:

* National Fire Protection Association

Batterymarch

Park

Quincy, Massachusetts 02269

Panel A

Electrical

requirements

Electrical Shock Hazard

Electrical ground is required on this

appliance.

Do Not ground to a gas pipe.

Do Not modify the power supply cord

plug. If it does not fit the outlet, have a

proper outlet installed by a qualified

electrician.

Do Not have a fuse in the neutral or

grounding circuit. A fuse in the neutral

or grounding circuit could result in an

electrical

shock.

Do Not use an extension cord with this

appliance.

Check with a qualified electrician

if you

are in doubt as to whether the

appliance

is properly grounded.

Failure to follow these instructions could

result in serious injury or death.

If codes permit and a separate grounding

wire is used, it is recommended

that a

qualified electrician

determine thal the

grounding path is adequate.

A 115-volt, 60-Hz, AC-only, fused

n electrical supplv is reauired. The

total ampere load used'including

the

range hood, must not exceed 90% of the

rated capacity

of the circuit. The ampere

rating of the range hood is located on the

serial/rating

plate located on the underside

of the range hood.

It is the personal responsibility and

n obliaation

of the customer to

contact

a qualified electrician

to assure

that the electrical installation is adequate

and in conformance

with the National

Electrical Code ANSI/NFPA 70 - latest

edition* and all local codes and

ordinances,

The range hood must be

n connected

with copper wire only.

The range hood should be

n connected

directly to the fused

disconnect

(or circuit breaker) box through

flexible armored or nonmetallic

sheathed

copper cable. A U.L.-listed strain relief must

be provided at each end of the power

supply cable. Wire sizes (COPPER WIRE

ONLY) and connections

must conform with

the rating of the appliance

as specified on

the serial/rating

plate.

Wire sizes must conform to the requirements

of the National Electrical Code ANSI/NFPA

70 - latest edition*, and all local codes

and ordinances.