Whirlpool Build-in 30 inch Manuel d'instructions d'installation - Page 4
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} Whirlpool Build-in 30 inch. Whirlpool Build-in 30 inch 8 pages. 30" electric built-in cooktop with glass-ceramic smooth top
Également pour Whirlpool Build-in 30 inch : Instructions d'installation et manuel d'utilisation et d'entretien (24 pages)
Imprimer la page
Make Electrical Connection
GROUhDED
NEUTRAL
COPPER
GROUNDED
COLD
GROUND
WIRE
WATER
PIPE
\
(REMOVE
PAINT,
ETC.)
NUTS
FIRMLY
(MUST
BE TIGHT
ON PIPE)
Connect the flexible
armored cable
that extends
from
the surface
untt to the junction
box using
a sultable
strain
relief at the poir?t the armored
cable
enters
the
)lAnctloP box. Then make the electrical
connectlon
as
fI!lIWS
It is the personal
responsibility
and obligation
of the
customer
to contact
a qualified
Installer
to assure
that
tie electncal
installation
IS adequate
and is in confor-
i-lance with the National
Electrical
Code and local code
clrdlnances.
Electrical
ground
is required
on this appliance.
This appliance
is equipped
with copper
lead wires.
I; connection
is made to aluminum
house wiring,
use
clnly special
connectors
which
are approved
for join-
ing copper
and aluminum
wires in accordance
with the
National
Electrical
Code
and
local
codes
and
or-
dinances.
This appliance
IS
manufactured
with a white
r eutral power supply wire and a frame connected
green
(1,' bare) ground
wire twisted
together.
I+ local codes permit
c,onnection
of the frame ground-
ing conductor
to the neutral
(white)
wire, connect
the
Green (or bare wire) and white
wire from the supply
cable of the appliance
together
and the neutral
(white)
v/ire In the junction
box. Connect
the remaining
wires
from the supply
cable to the wires in the junction
box
See Figure
3.
If
local codes
DO NOT permit frame grounding
to the
reutral.
separate
the white (and green
or bare wires)
that extend
out of the end of the supply
cable
of the
appliance.
See Figure
5. Connect
the white wire from
the supply
cable to the neutral wire in the junction
box.
Connect
the black and red wire from the supply
cable,
UNGROUNDED
NEUTRAL
JUNCTION
FROM
POWER
BOX
\
SOYRCE
I
BARE
WIRE
to the corresponding
wires
in the junction
box. The
green
(or bare) wire must now be used to ground
the
appliance
in accordance
with local electrical
codes.
Connect
the green colored copper
(or bare) ground wire
to a grounded
cold water pipe*
(see Figure 4) or to the
grounded
lead in the service
panel.
Do not ground to
a gas supply
pipe.
Do not connect
to electric
power
supply
until appliance
is permanently
grounded.
Con-
nect the ground
wire before turning
on the power. (See
Figure
4.)
CAUTION
-
If connecting
to a four-wire
electrical
system
(MOBILE
HOME)
the appliance
frame
MUST NOT
be connected
to the neutral
wire of
the four-wire
electrical
system.
Separate
the white
(and green
or bare wires) that extend
out of the
end of the supply
cable of the appliance.
Connect
the white,
red and black
wires
from the supply
cable,
to the corresponding
wires in the junction
box. Connect
the green
(or bare) wire from the
supply
cable
to the ground
wire in the junction
box. (See Figure
5)
*Cold water
pipe must have metal continuity
to elec-
trical ground
and not be interrupted
by plastic,
rubber
or other
electrically
insulating
connectors
(including
water meter or pump) without
adding
a jumper
wire at
those
connections.
4