Whirlpool RJH 3330-1 Manuel d'installation et d'utilisation - Page 2
Parcourez en ligne ou téléchargez le pdf Manuel d'installation et d'utilisation pour {nom_de_la_catégorie} Whirlpool RJH 3330-1. Whirlpool RJH 3330-1 6 pages. Whirlpool microshelf hood installation and operating instructions rjh 3330-1
Imprimer la page
12" HIGH
CABINET
+"x
IO"ELBOW
RAIN
CAP
SHELF/
HOOD
TRANSITION
DUCT
PROVIDED
WITH
HOOD
Figure 2
II.
VENTED
INSTALLATION
For
ventless
installation,
Kit
RCH3630
must
be
installed.
A. Assembling
and Installing
to Wall
1.
Select the area for installation,
making
sure
you have an electrical
supply
available.
See the
shaded
area in Figure
3. This
is the area the
ON BACK
WALL
electrical
supply
must enter.
ELECTRICAL
INLET AREA \
Figure 3
*When installing
the Microshelf
Hood in a ventless
installation,
this
dimension
is 16%". See the
instructions
with the ventless
kit (RCH3630)
for
details.
CAUTION:
Due to the
amount
of weight
the
Microshelf
Hood must support,
you must make
sure the Microshelf
Hood is mounted
to 2 vertical
wall studs and into the wall covering which must be
at least %" thick sheet rock, with 4 wall anchor
bolts.
2.
If the Microshelf
Hood is mounted to a wall that
does not meet the above recommendations,
the
weight
of the microwave
oven
may cause
the
Microshelf
Hood
to pull
away
from
the wall
resulting
in personal
injury or property
damage.
NOTE:
If the Microshelf
Hood is to be installed
above a freestanding
range, disconnect
the power
from the range and move the range out of the
opening
in the cabinets.
This will allow for more
access to the installation
area.
If installing
the Microshelf
Hood above a built-in
cooktop or set-in range, lay a protective
cover over
the cooktop
during the installation.
This may help
prevent damage to the cooktop
(in case you drop
something)
and it will prevent dust and dirt from
accumulating
on the cooktop
during
installation.
3.
Mark a line on the back wall 15" down from the
upper cabinets 30" long centered
between theside
cabinets
or allotted
space. See Figure 3.
4.
Locate the 2 wall studs in the area you have
selected for mounting
the microwaveoven.
IF YOU
DO NOT
KNOW
HOW TO LOCATE
A WALL
STUD,
CONSULT
A
LOCAL
BUILDING
CONTRACTOR
FOR HELP.
NOTE:
If 2 studs are not located on the line drawn
in Figure 3, DO NOT attempt
to install the shelf
hood.
5.
Line the top of the hanging
bracket up with the
line drawn on the wall in Figure 3. Move the bracket
to the left or right within the allotted 30"space
until
the center line of the 2 studs line up with 4 holes in
the hanging
bracket.
Neither edge of the bracket
should be closer than l/2" to the side cabinets or the
end of the 30" allotted
space. (See Figure 4).
6.
Mark and drill four 3/16 dia. pilot holes in the
studs for the l/4" dia. x 2" long lag bolts provided.
CLEARANCE
TO CABINET
STUD+
1
-MARK
HOLES-REMOVE
HANGING
BRACKET
AND
DRILL
&'
DIA.
HOLE
IN
II
+
SHEET
ROCK
Figure 4
7.
Mark 2 holes
on each end of the hanging
bracket.
Remove bracket and drill four 7/16" dia.
holes.
8.
Insert four hollow
wall anchor
bolts into the
four 7/16" dia. holes in thesheet
rock. Anchor bolts
are provided
in installation
pack. Rotate anchor
bolts screws 5-10 revolutions
to hold each anchor
bolt in place. These will be completely
tightened
later. (See Figure 5).
Page 2