Yamaha DTX542K Manuel d'assemblage

Parcourez en ligne ou téléchargez le pdf Manuel d'assemblage pour {nom_de_la_catégorie} Yamaha DTX542K. Yamaha DTX542K 2 pages. Dtx drums series

Imprimer la page

DTX522K/DTX542K

This manual describes the standard assembly procedure for the DTX522K and DTX542K electronic drum kits. It covers assembly and wiring of the kit as

shown below. When you have completed all of the steps described, you will be ready to turn on the drum module and start playing.

Example of standard assembly

Cymbal pad

Tom pads

Cymbal pad

(hi-hat)

Drum module

Snare pad

Kick pad

Hi-hat controller

Safety Precautions

The purpose of the precautions detailed below is to ensure that this electronic drum kit can be used safely without fear of injury or property damage. As a means of indicating

the severity and immediacy of any risk of injury or property damage resulting from incorrect operation, these precautions are classified as either WARNING or CAUTION. The

instructions displayed together with these precautions are extremely important in terms of ensuring safety, and therefore, they should be fully observed.

* After reading this Assembly Manual, ensure that it is kept in a safe, convenient location for future reference.

* Be sure to also read the Assembly Manuals and/or Owner's Manuals that came with your pads and rack.

Failure to observe the precautions described below can result in

WARNING

serious injury or even death.

• Young children using this electronic drum kit should be supervised by a guardian to eliminate any

possibility of injury.

• Holders for cymbal and tom pads have sharp tips. In order to avoid injury, therefore, you should

take special care whenever handling these components.

• The anti-slip stoppers on kick pads and foot pedals have sharp tips. In order to avoid injury, there-

fore, you should take special care whenever handling these components.

• Be sure to securely tighten nuts and other fasteners when setting up this electronic drum kit. In

addition, be sure to proceed slowly when loosening nuts. If this precaution is not observed, pads

may fall off or the rack may collapse or fall over, possibly causing injury.

• Do not setup this electronic drum kit on a slope, on an unstable platform, or on any other unsafe

surface. If this precaution is not observed, it may topple over or fall, possibly causing injury.

• Whenever setting up this electronic drum kit, ensure that cables and the like are arranged safely. If

someone were to trip on a cable, the kit could topple over and cause injury.

• Under no circumstances should this electronic drum kit be disassembled or customized. Failure to

observe this precaution can result in injury or malfunction.

• Do not sit or stand on the rack. Doing so could cause it to fall over or break, possibly causing

injury.

* Yamaha Corporation reserves the right to change or modify products or specifications at any time without prior notice.

U.R.G., Digital Musical Instruments Division

Assembly Manual

IMPORTANT

This manual describes the process of assembling drum pads and a

Cymbal pad

drum module to an already assembled RS502 Electronic Drum Rack.

Before starting the steps below, therefore, be sure to assemble your

RS502 as described in the Owner's Manual that came with it.

NOTICE

Before starting assembly, lay a drum mat (sold separately) on the floor.

Tom pad

Alternatively, you can place cardboard from the drum kit packaging or

the like on the floor to prevent it from being scratched. This is particu-

larly important when using the HH65 Hi-hat Controller and KP65 Kick

Pad.

Electronic drum

rack

Please read carefully before proceeding.

Failure to observe the precautions described below can result in

CAUTION

injury and/or property damage.

• Mind your fingers when adjusting clamps. They can easily be crushed if care is not taken during

this operation.

• Be careful with the tips of supports, arms, screws, and the like. Fingers can easily be injured by

sharp tips if these components are not handled carefully.

• Do not place hands or feet under a kick pad or foot pedal. Doing so could result in injury.

• Do not use the electronic drum kit's rack to hold acoustic drums. Doing so could cause clamps to

break and the drums to fall off, which in turn could lead to injury.

NOTICE:

Usage Precautions

• When connecting and disconnecting cables, be sure to hold the plug and not the cable itself. In

addition, avoid placing heavy items on top of cables and do not allow them to touch sharp edges.

Failure to avoid these precautions can lead to cable breakage and disconnection.

• Do not climb onto the electronic drum kit and avoid placing heavy objects on it. Failure to observe

this precaution can result in malfunction.

• Avoid using or storing the electronic drum kit in very hot locations (i.e., in direct sunlight, in close

proximity to a heater, or in a closed vehicle) or in highly humid locations (i.e., in a bathroom or out-

doors in wet weather). Failure to observe this precaution can lead to warping, discoloration, mal-

function, or breakdown.

• Avoid cleaning the electronic drum kit with organic solvents, paint thinner, or alcohol as these sub-

stances can cause warping and discoloration. Instead, we recommend you remove dust using a soft

dry cloth or wipe clean using a moist, tightly-wrung cloth. If the electronic drum kit is very dirty, first

wipe the dirt away using a cloth moistened with a neutral detergent solution and tightly wrung. Fol-

lowing this, wipe away the detergent solution using a cloth soaked in water and tightly wrung.

Open the boxes to reveal their contents.

After opening up the packages containing your electronic drum kit, please verify that all of the following components are present.

211POAP*.*-01A0

Printed in Vietnam

ZE16420

Components of both DTX522K & DTX542K

 XP80 Snare Pad

 PCY135 Cymbal Pad

(x1)

 HH65 Hi-hat Controller

 Hi-hat holder (x1)

(x1)

 Stopper for PCY100 and PCY135

(x3)

 Felt pad for

PCY135 (x1)

PCY100 (x2)

Components of DTX522K only

 TP70 Tom Pad (x3)

 Clamp bolt

(for XP80; x1)

Assemble the RS502 Electronic Drum Rack.

For instructions on how to assemble the RS502 Electronic Drum Rack, refer to the Owner's Manual that came with it.

Assemble the hi-hat holder, the pads, and the drum module to the electronic drum rack.

Assembling the hi-hat holder

Remove the drum module clamp a and the left leg b from the left side of the

rack.

Drum module

clamp a

Left leg b

 PCY100 Cymbal Pad

 KP65 Kick Pad

 RS502 Electronic Drum Rack (x1)

 RS502 Owner's Manual (x1)

(x2)

(x1)

 Nine-channel snake cable (x1)

 DTX502 Drum

Module (x1)

 Cable band (x6)

 Tuning key (x1)

 Module holder (x1)

 DTX522K/DTX542K Assembly Manual (this booklet; x1)

 PCY100/135/155 Owner's Manual (x1)

 HH65 Owner's Manual (x1)

 XP70/80 Owner's Manual (x1)

 KP65 Owner's Manual (x1)

Components of DTX542K only

 Wing bolt

 XP70 Tom Pad (x3)

 Clamp bolt

(for TP70; x3)

 TP70 Owner's Manual (x1)

Assemble the holder clamp for the hi-hat holder, ensuring that it is oriented as

shown in the figure. Following this, reassemble the left leg b and the drum mod-

ule clamp a.

Hi-hat holder

Holder clamp

Drum module

clamp

Left leg

 Power adaptor (x1)

* May not be included

depending on your

particular area. Please

check with your Yamaha

dealer.

 Module holder

screw (x2)

 DTX502 Owner's Manual (x1)

(for XP70 or XP80; x4)

Continued on rear.