Yamaha MA2030 Manuel du propriétaire

Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} Yamaha MA2030. Yamaha MA2030 5 pages. Yamaha power amplifiers technical specifications
Également pour Yamaha MA2030 : Manuel du propriétaire (2 pages), Spécifications techniques (2 pages)

Imprimer la page

ZJ24810

First, please carefully read the "IMPORTANT SAFETY INSTRUCTIONS" on the reverse side.

Thank you for your purchase of the Yamaha MA2030/PA2030 power ampliﬁer. Please read through this

manual carefully before beginning use, so that you will be able to take full advantage of the device's

various functions. After you have read the manual, keep it in a safe place.

• The illustrations as shown in this manual are for instructional purposes only.

• The company names and product names in this manual are the trademarks or registered trademarks of

their respective companies.

• In this manual, the

mark indicates content that is unique to the MA2030, and

content unique to the PA2030. Contents that are common to both have no marks.

• Ampliﬁer illustrations are mainly from the MA2030. Where necessary, illustrations of the PA2030 are also

shown.

Features

• Supports both kinds of speaker connection: high-impedance connection and low-impedance

connection.

• Equipped with digital processor (Feedback Suppressor, Ducker, Leveler).

• Optional PA2030 expansion ampliﬁer enables connection of additional speakers.

Included items

• Power cord (2.0m)

• Euroblock plugs (3-pin, 3.50mm pitch) x 1

, x 2

• Technical Speciﬁcations (English only): includes block diagram, dimensions, and input/output

speciﬁcations.

• Owner's Manual (this sheet)

Setup

Step

Option

Speakers

Step

Front panel

Portable audio player,

Option

etc.

Step

Speaker expansion

Rear panel

CD players, tuners, etc.

Step

Option

To AC outlet

Step

Volume adjustment

Step

Connecting Speakers

Change the setting depending on the speaker connection (high- or low-impedance connection), the kind

of speakers, and the installation location of the speakers. Refer to "Connecting Speaker Cables" at the

right bottom on this page and the explanation of high-impedance connection, etc. at the following URL.

Yamaha Pro Audio site: "Better Sound for Commercial Installations":

http://www.yamahaproaudio.com/global/en/training_support/better_sound/

Caution

• Before connecting speakers, make sure that the power of the device is turned off. If the power is on, there is a risk of

electrical shock.

• Ensure that load is not applied to the speaker cable.

• In a high-impedance installation, make sure that the sum of the power input ratings of the speakers to be connected

does not exceed 60W.

• In a low-impedance installation, make sure that the total impedance of speakers to be connected is at least 3 ohms.

■

High-impedance Connections (60W x 1 channel)

Maximum output

voltage: 100V

voltage: 70V

Set the speaker output to high-impedance by setting the [OUTPUT] switch to

[100V] or [70V] corresponding to the maximum output voltage.

Use speaker cables to connect the [SPEAKERS A]

terminal to the positive "+"

terminals of the speakers, and the [SPEAKERS B]

terminal to the negative "-"

terminals.

In case of high-impedance connection, the [SPEAKERS A]

and [SPEAKERS B]

not used. Do not connect to the terminals.

Note

The speaker output is processed through a high pass ﬁlter (80Hz, 18dB/oct.).

■

Low-impedance Connections (30W x 2 channels)

Speaker impedance

Set the speaker output to low-impedance connection by setting the [OUTPUT] switch

to [4Ω 3Ω].

Set the [SETUP] DIP switch 1 to [4Ω] (up, impedance: 4Ω or more) or [3Ω] (down,

impedance: 3Ω to 4Ω) corresponding to the specifications of the speakers to be

connected.

Connect the [SPEAKERS A]

terminals to the "+"/"-" terminals of the first

speaker, and the [SPEAKERS B]

terminals to the "+"/"-" terminals of the second

indicates

speaker.

■

Configuration of Speaker Output Signal

Connecting Yamaha Speakers

Setting mono/stereo output

[SETUP] DIP switch 4/5

[SETUP] DIP switch 7

Setting the [SETUP] DIP switches optimizes the

In a low-impedance installation, if speakers are

output signal to match Yamaha speakers designed

placed in a stereo arrangement, set to stereo

for commercial installations.

output.

[SETUP] DIP switch

Surface

High-impedance

Yamaha speakers

down

mount-type

connections

designed for

commercial installations

Ceiling-type down

down

Low-impedance

connections

Non-Yamaha speakers

—

—: Setting is not required. (Either up or down can be used.)

*1: When stereo audio is output, the left channel signal

is output from the [SPEAKERS A] terminals and the

right channel signal is output from the [SPEAKERS B]

terminals.

Step

Connecting External Devices

RCA type

mini-stereo

Microphones

type

MA2030 front panel

MA2030 rear panel

Connect a BGM (background music) tuner, a CD player, a portable audio player, etc. to the stereo input jacks

of this device.

Jack position

Jack name

Front panel

[ST IN 1] jack

mini-stereo type (unbalanced input)

MA2030

[ST IN 2] jack

Rear panel

RCA type (unbalanced input)

[ST IN 3] jack

Euroblock connector (balanced input; connect with supplied

Control Panel

PA2030

Rear panel

[LINE IN] jack

Euroblock plugs), RCA type (unbalanced input)

(DCP1V4S)

Note

Refer to "Attaching Euroblock Plugs" for Euroblock plug installation.

Make sure that this device and all devices to be connected are turned off.

Connect this device and any external devices with appropriate cables.

Leveler (suppressing wide playback volume variations)

[SETUP] DIP switch 6

The Leveler function automatically suppresses and corrects for large changes

in the playback volume from external devices for a more consistent sound,

such as when reproducing BGM (background music).

Step

Connecting Power Cord and Turning On

AC IN connector

MA2030 front panel

Make sure power switches of this device and devices connected to this device are

turned off (in

position).

Turn the [VOLUME] knob all the way to the left.

Connect the supplied power cord to the AC IN connector.

Insert the power cord plug into an appropriate outlet.

After turning on the connected devices (portable audio players, CD players, etc.), turn

on this device.

Note

• Before turning on the power, please check that there are no problems with the cabling, connections, and so on.

• When turning the system off, turn off this device, and then connected devices.

terminals are

Step

Adjusting Volume

[SETUP] DIP switch

4Ω or more

3Ω to 4Ω

MA2030 front panel

down

Select a stereo input by rotating the [ST SOURCE] knob.

The [ST SOURCE] indicator corresponding to the selected input signal lights.

Input audio signal from the external device, and confirm that sound is being output

from the speakers by gradually rotating the [VOLUME] knob to the right.

Make sure that the [VOLUME SIGNAL] indicator lights according to the sound input and that sound

comes from the speakers.

Matching the volume levels of external devices (including microphones)

When connecting two or more external devices, you can lower the volume of the louder devices (or

microphones) to match the level of the faintest device. If you are using microphones, follow the instructions in

"Option 1 Using Microphones" before executing the operation below.

Select the stereo input with the loudest sound by rotating the [ST SOURCE] knob.

Press and hold the [ST SOURCE] knob until the [ST SOURCE] indicator flashes.

Rotate the [ST SOURCE] knob to the left until the volume decreases to the point that

lowers as loud as that of the faintest sounding stereo input (or microphones).

As the volume becomes fainter, the ﬂashing rate of the [ST SOURCE] indicator becomes slower.

Push the [ST SOURCE] knob to complete the adjustment.

The [ST SOURCE] indicator lights.

Note

Adjustable range: -18dB – 0dB

—

Mono output

Option

Using Microphones

down

Stereo output (*1)

Phone

XLR

MA2030 front panel

Euroblock

Turn the [MIC IN 1] knob or the [MIC IN 2 GAIN] trimmer all the way to the left, and

connect a microphone to the [MIC IN 1] jack or the [MIC IN 2] connector.

Set the [VOLUME] knob to roughly a 2:00 position.

Loudly speak into the microphone, and turn the [MIC IN 1] knob or the [MIC IN 2 GAIN]

trimmer to the right until the output signal is not distorted.

If you input a loud voice but the output is small, raise the volume with the [VOLUME] knob.

If the sound out of the speakers is too loud, lower the volume with the [MIC IN 1] knob or the [MIC IN 2

PA2030 rear panel

GAIN] trimmer.

Make sure the input from external devices matches the volume levels of the

microphones and the external devices.

Refer to "Matching the volume levels of external devices (including microphones)" in "Step 4 Adjusting

Jack type

Volume" for instructions.

Note

• To adjust the [MIC IN 2 GAIN] trimmer, use a slotted screw driver.

• Refer to "Attaching Euroblock Plugs" for installation of Euroblock plugs.

• The input signal is always processed through a high pass filter (120Hz, 12dB/oct.) to cut off low frequency signals

as well as a Feedback Suppressor to suppress howling.

Ducker (lowering the volume of the other channels automatically when a

microphone signal is input)

[SETUP] DIP switch 2/3

Jack/connector

[MIC IN 1]

[SETUP] DIP switch

Ducker disabled

Leveler disabled

Ducker enabled

down

Leveler enabled

down

Option

Expanding Speakers

Power cord

To AC outlet

MA2030 rear panel

Connecting the MA2030 and PA2030 lets you increase the number of driven speakers. Connect the [LINE

OUT] jacks of MA2030 and the [LINE IN] jacks of PA2030.

Connecting Yamaha Digital Control Panel DCP1V4S to MA2030 enables you to control the volume, to

switch inputs, etc. remotely.

PA2030 front panel

The functions of the knob and the switches of DCP1V4S can be conﬁgured with DIP switches at the back

of DCP1V4S.

Panel

Note

Euroblock

The [SPEAKERS] output connectors on the rear panel are barrier strip type connectors. The connections

are described below for two methods: using a spade lug and using a bare conductor.

Ensure that load is not applied to the speaker cable.

Note

MA2030 rear panel

When using a spade lug

Loosen the screw, insert the spade lug all the

way from below, and tighten the screw.

[MIC IN 2]

Note

• If both Duckers of the [MIC IN 1] jack and the [MIC

IN 2] jack are enabled, the Ducker for the [MIC IN

1] takes priority.

• Activating the Ducker lowers the output volume of

down

the stereo inputs by 24dB and mutes that of the

other microphone input.

Terminal

screw

Note

RCA

PA2030 rear panel

Changes by several knobs can be locked, so that the settings of the device are not affected by accidental

touch or unauthorized operation. The [ST SOURCE], [SOURCE EQ BASS] and [SOURCE EQ TREBLE]

knobs can be locked.

Note

Option

Operating with Control Panel

RJ-45

Yamaha Digital Control Panel

DCP1V4S

(maximum: one unit)

Rear panel

When connecting to MA2030,

set the DIP switch 4 to ON

(termination setting).

MA2030 rear panel

Ethernet straight cable

Sets the panel ID

(CAT5e or more; 200m or less)

Volume: Adjusts the volume output

DIP switch

Knob

Switch 1

Switch 2

Switch 3

Switch 4

to the [SPEAKERS] terminals and

1 2 3 4

the [LINE OUT] jacks.

—

Stereo 1/2/3: Switches to stereo

input 1/2/3.

Mic. 1/2: Turns on/off microphone

Stereo 1

Stereo 2

Stereo 3

—

input 1/2. When a microphone

is on, the switch indicator of the

Mic. 1

Mic. 2

Mic. 1

Mic. 2

control panel lights and the stereo

input is muted.

Mic. 1

Mic. 2

• If the panel ID is set to 3, the

Mic. 1

Mic. 2

stereo input is not muted even

Volume

though the microphone is on.

Mic. 1

—

Mic. 1

—

• If the panel ID is set to 7, the

microphone stays on while

—

Mic. 2

—

Mic. 2

holding the switch.

: A chime sounds when the

microphone is turned on/off

Mic. 1

Mic. 2

—

—: Does not work. (No function is

assigned.)

Mic. 1

Mic. 2

—

Refer to "DCP1V4S Owner's Manual" for DCP1V4S installation.

Connecting Speaker Cables

Caution

Connect the cables so that the ampliﬁer's "+" and "-" symbols match those of the speaker. If they are reversed,

the phase will be reversed and the sound will not be output correctly.

When using a bare conductor

Loosen the screw, wrap the conductor wire around

the barrier strip terminal, and tighten the screw. Be

sure that the bare wire does not touch the chassis.

Speaker cable

≥3.2mm

(≥ 0.13")

15mm*

(0.6")

≤5.8mm

(≤0.23")

* Actual size

Attaching Euroblock Plugs

Loosen

Approx. 5 mm

Slotted

(approx. 0.2")

Tighten

screwdriver

Euroblock plug

• You must use the supplied Euroblock plugs. If the plugs have been lost, please contact your Yamaha dealer.

• To prepare the cable for attachment to a Euroblock connector, strip the wire as shown in the illustration using

stranded wire to make connections. With a Euroblock connection, stranded wires may be prone to breakage

because of metal fatigue due to the weight of the cable or due to vibration. When rack mounting your device,

use a lacing bar when possible to bundle and fasten the cables.

• Do not tin (solder) the exposed end.

Loosen terminal screws.

Insert cables.

Securely tighten terminal screws.

Insert the Euroblock plug into the [MIC IN 2] terminal of MA2030 or the [LINE IN]

terminal of PA2030.

Panel Lock

Adjust the [ST SOURCE], [SOURCE EQ BASS] and [SOURCE EQ TREBLE] knobs

to the desired fixed settings.

Turn off the power.

Set DIP switch 8 to the downward position.

Turn the power back on again.

To unlock, turn off the power, set DIP switch 8 to the upward position, and turn on the power.

Wire

should not

touch the

chassis.