Yamaha HS10W Manuel du propriétaire - Page 12

Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} Yamaha HS10W. Yamaha HS10W 17 pages. Hs series powered monitor speaker and powered subwoofer
Également pour Yamaha HS10W : Manuel du propriétaire (16 pages), Manuel d'entretien (23 pages)

Imprimer la page
Yamaha HS10W Manuel du propriétaire

Rear Panel

HS80M, HS50M
1
POWER switch
Turns power to the speaker on or off. When the power is
turned on the tuning fork mark on the front panel will light.
"
LEVEL control
Adjusts the overall output level.
#
INPUT 1/2 connector
These are balanced XLR-type and phone type input
connectors.
Do NOT use both the XLR and Phone type connector at the same
time. Please connect to only one of these connectors.
$
MID EQ switch
Adjusts the level of the mid-frequency range. Setting the
switch to the "0" position produces a flat frequency response.
With the "+2 dB" setting, the mid range is boosted by 2 dB.
With the "-2 dB" setting, the mid range is cut by -2 dB.
(Center frequency is 2 kHz.)
%
ROOM CONTROL switch
Corrects the low frequency exaggeration caused by reflecting
off ceilings, walls and floors. Setting the switch to the "0"
position produces a flat frequency response. With the "-2 dB"
setting, the range below 500 Hz is cut by 2 dB. With the "-4
dB" setting, the range below 500 Hz is cut by -4 dB.
12
HS80M/HS50M/HS10W Owner's Manual
HS80M
HS50M
MID EQ
MID EQ
+2dB
+2dB
0dB
0dB
-2dB
-2dB
2kHz
2kHz
ROOM CONTROL
ROOM CONTROL
0dB
0dB
-2dB
-2dB
-4dB
-4dB
500Hz
500Hz
HIGH TRIM
HIGH TRIM
+2dB
+2dB
0dB
0dB
-2dB
-2dB
2kHz
3kHz
LOW CUT
LOW CUT
FLAT
FLAT
80Hz
80Hz
100Hz
100Hz
+4dB
LEVEL
MIN
-10dB
1
INPUT
2
+2dB
MID EQ
0
-2dB
0
ROOM
-2dB
CONTROL
-4dB
+2dB
HIGH
0
TRIM
-2dB
FLAT
80Hz
LOW CUT
100Hz
POWER
OFF
ON
AC IN
&
HIGH TRIM switch
Adjusts the level of high-frequency range.
HS50M:
Setting the switch to the "0" position produces a flat
frequency response.
With the "+2 dB" setting, the range above 3 kHz is
boosted by 2 dB. With the "-2 dB" setting, the
range above 3 kHz is cut by -2 dB.
HS80M:
Setting the switch to the "0" position produces a flat
frequency response.
With the "+2 dB" setting, the range above 2 kHz is
boosted by 2 dB. With the "-2 dB" setting, the
range above 2 kHz is cut by -2 dB.
'
LOW CUT switch
Cuts the low-frequency range. With the "80 Hz" setting the
range below 80 Hz is cut. With the "100 Hz" setting the range
below 100 Hz is cut.
(
AC IN Connector
Connect the supplied power cable here. First connect the
power cord to the speaker, then insert the power cord plug
into the AC outlet.
"
#
$
%
&
'
!
(