Clark-Reliance Reliance Simpliport 180 Instructions d'installation, d'utilisation et d'entretien - Page 2

Parcourez en ligne ou téléchargez le pdf Instructions d'installation, d'utilisation et d'entretien pour {nom_de_la_catégorie} Clark-Reliance Reliance Simpliport 180. Clark-Reliance Reliance Simpliport 180 4 pages.

Imprimer la page

The Reliance

Simpliport

been designed to accept 120VAC or 240 VAC power

sources and for a service life of up to 7 years. The

LED Illuminators are weatherproof and are rated safe

for use in ordinary locations

STORAGE and HANDLING

All units should be inspected upon receipt to ensure

that no damage has been incurred during transit. If

there is a claim due to damage, it should be filed with

the carrier immediately. Units should be stored in a

dry and sheltered area prior to installation, in a secure

manner where they can neither fall, nor be struck by

other objects. The temperature for the storage area

should not be outside of the acceptable operating

temperatures of -40F (-40C) to170F (77C).

COMPONENTS

There are four main components that make up the

Simpliport Illuminator Assembly: the LED

Illuminator, the front viewing hood, the power supply,

and the cable connecting the power supply to the LED

Illuminator. The cable may have more than one piece

depending on the required distance between the

Illuminator and the power supply. In most cases, the

power supply will be mounted directly to the LED

Illuminator.

INSTALLATION

CAUTION: All LED Illuminators are tagged

with the service conditions for that particular unit.

This information is located on the power supply

housing. The ratings should be reviewed prior to

installation and again prior to start-up, to ensure

proper operation in the installed environment.

IMPORTANT

Never remove the blue cord between the power

supply and illuminator while power is applied.

Doing so will cause permanent damage to the

LEDs.

Note: All installation steps should be performed by

a qualified electrician and should be executed in

accordance with all applicable national and local

codes.

16633 Foltz Parkway ● Strongsville, OH 44149 USA Telephone: +1 (440) 572-1500 ● Fax: +1 (440) 238-8828

180 LED Illuminator has

www.clark-reliance.com ● [email protected]

The LED Illuminator and power supply should be

checked to ensure that they contain no foreign matter,

and that the conduit hole is in line with existing

conduit.

Step by step instructions:

1) Install the (4) 5/16-18 Wing Screws into the

mounting lugs on both sides of the Simpliport

Gage, leaving approximately ¼" unthreaded

(Ref. Fig. 1) Note: If retrofitting a new

illuminator and hood assembly, remove the

existing mounting bars before installing the

Wing Screws.

2) Install the Illuminator first by attaching the top

slots onto the Wing Screws and lowering the

bottom slots into place. The Illuminator is

assembled to the back of the gage as you will

view the level. Note: The Simpliport Gage

must be viewed with the packing nuts facing

slightly to the left. Make sure that the

Illuminator and viewing hood are in the

correct orientation to the Simpliport Gage

(Fig. 2).

3) Next assemble the front viewing hood to the

Simpliport Gage, making sure that the slots are

on the outside of the illuminator sheet metal

slots. Attach the top slots onto the Wing Screws

and lower the bottom slots into place. The

viewing hood is now assembled to the front of

the gage as you will view the level.

4) Tighten all four of the Wing Screws to secure

both the illuminator assembly and the viewing

hood.

5) The unit's power supply has wire leads and a

fuse ready to connect to the incoming AC

power source. Remove the enclosure lid to

access wiring. Connect incoming AC power

source per local and National Electric Codes.

The fused (red) wire is the "Hot" (+) and the

remaining white or blue wire is the "common"

(-).

6) The power supply can be remote mounted if

desired. After remote mounting of power

supply, if the blue power cord will not reach the

power supply, contact your local representative

or factory for the required extension cable .