Directed Xpresskit DBALL2 Manuel d'installation et de référence rapide - Page 7

Parcourez en ligne ou téléchargez le pdf Manuel d'installation et de référence rapide pour {nom_de_la_catégorie} Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 16 pages. Ford5 remote start ready (rsr) installation
Également pour Directed Xpresskit DBALL2 : Manuel d'installation (12 pages), Manuel d'installation (19 pages), Manuel d'installation (18 pages), Manuel (14 pages), Manuel d'installation (13 pages), Manuel d'installation (14 pages), Manuel d'installation (19 pages), Manuel d'installation (16 pages), Manuel d'installation (20 pages), Manuel d'installation (15 pages), Manuel d'installation (18 pages), Manuel d'installation (16 pages), Manuel d'installation (18 pages), Manuel d'installation (16 pages), Manuel (19 pages), Manuel d'installation (11 pages), Manuel d'installation (10 pages)

Imprimer la page
Directed Xpresskit DBALL2 Manuel d'installation et de référence rapide
Platform: DBALL2
Firmware: GM6
Installation Type 3c, T-Harness THGM610 Rev. 1 & 2, T-02 (without RFLCHGM)
WARNING!
We recommend using the Wiring Diagram (
RFLCHGM) will draw 15-20mA more on the vehicle, when it is parked and the engine is turned off.
Using Wiring Diagram (
without
opening. To preserve OEM remote starter functionality, use the Wiring Diagram (
Use connectors
D2D
labeled GM6
only
Ignition
Barrel
To vehicle
6-pin connector
T-01
T-02
T-02
Cadillac Escalade
Chevrolet Avalanche
Chevrolet Express Van
Chevrolet Silverado 1500
Chevrolet Silverado 2500/3500
Chevrolet Suburban
Chevrolet Tahoe
GMC Savana
GMC Sierra 1500
GMC Sierra 2500/3500
GMC Yukon
Hummer H2
If the RAP Off wire is not connected, the radio will turn OFF but some lights will remain ON in the central console for 10 minutes. Connect this wire
[1]
(Green/Black, pin 2/12) to the driver door sense trigger (Gray/Black) to avoid the issue. RAP Off: Refer to page 9 for wire color and location.
Only required if no OEM hood pin.
[2]
with
RFLCHGM) on page 3, especially if the vehicle is not used daily. The Wiring Diagram (
RFLCHGM) can deactivate OEM remote starter functionality, OEM fob and smart phones, due to the accessory wire
To
Immobilizer
Control
Module (ICM)
(under ignition switch,
black connector)
(+) Ignition Status Output: Pink:7
Ignition
n/a: Black/White:1
Connector
(-) RAP Off: Green/Black:2
[1]
n/a: Violet/Brown:8
n/a: Violet/Green:9
(-) Driver
Door Sense
Trigger
[1]
NOT
USED
with
RFLCHGM) on page 3.
(+) Ignition Input
To
Immobilizer
Control
Module (ICM)
(vehicle side)
RF
Prog.Button
LED
T-Harness
THGM610
(Optional)
Single Wire CAN:
Dk.Green pin 1
Rev.: 20151221
without
(-) Ground
(-) Ground
(+) 12V
(+) 12V
(-) Parking Lights
(-) Parking Lights
(-) Hood Status Input
[2]
Hood Pin
n/a: White/Black
Remote Start Safety
Override Switch
(+) 12V
DBALL/
RX
(-) Ground
DBALL2
P#: XKD2D65
TX
NOT USED
Cut away the 4-pin
connector and connect
the three wires to the
OBDII 16-pin connector.
CAN High: Tan/Black, pin 6
Diagnostic connector
1
8
OBDII
(connector side view)
9
16
CAN Low: Tan, pin 14
© 2015 Directed. All rights reserved.
Page 7