Directed 4115V Référence rapide Manuel d'installation - Page 2
Parcourez en ligne ou téléchargez le pdf Référence rapide Manuel d'installation pour {nom_de_la_catégorie} Directed 4115V. Directed 4115V 2 pages. Remote start with keyless entry
Imprimer la page
Programming System Features
The System Features Learn Routine dictates how the unit operates. It is possible to access and change most of the
feature settings using the Valet button.
1.
Turn the ignition on, then off.
2.
Select a Menu. Within 10 seconds, Press and hold the Valet button. The number of LED flashes and horn
honks indicates the menu number. A single LED flash and honk indicates menu 1. Two LED flashes and 2
honks indicates menu 2.
3.
When the desired menu LED flashes and honks are heard, release the Valet button.
4.
Select a Feature, within 10 seconds. Press and release the Valet button the number of times correspond-
ing to the feature you wish to change. Then press and hold one more time to select the feature. The LED
flashes and the horn honks to indicate which feature is selected.
5.
Program the Feature. While holding the Valet button, you can program the feature using the remote
control.
Pressing the button on the remote control advances to each feature option. The LED flashes and the horn honks
indicating which option is selected.
Once a feature is programmed:
•
Other features can be programmed within the same menu
•
Another menu can be selected
•
The learn routine can be exited if programming is complete
To access another feature in the same menu:
1.
Press and release the Valet button the number of times necessary to advance from the feature you just pro-
grammed to the next one you want to program.
2.
Then press the Valet button once more and hold it.
To select another menu:
1.
Press and hold the Valet button.
2.
After 3 seconds, the unit advances to the next menu, the horn honks and LED flashes indicating which menu
has been accessed.
The learn routine exits if any of the following occurs:
•
The ignition is turned On
•
There is no activity for 30 seconds
•
The Valet button is pressed too many times
Bitwriter - Only Options
If programming with the Bitwriter®, the learn routine can be locked or unlocked. If the learn routine has
previously been locked, it must be unlocked with Bitwriter® - this cannot be done manually with the Valet
button.
The Bitwriter®
gives you access to a wider range of system options. These additional features and the adjust-
ments that may be programmed are described in the table below.
Menu Item
Feature
Default
1
Engine Runtime
12 min.
2
Diesel start type
Off
3
Diesel start delay time (seconds)
15 sec
4
Virtual Tach Fine Tune
Not initialized
5
Remote control programming
Unlocked
6
Feature Programming
Unlocked
© 2012 Directed. All rights Reserved.
Feature Menus
Default settings are in bold type.
Menu 1
Feature #
Feature
Opt. 1
1
Horn function
Off
2
Ignition con-
On
trolled lock
3
Ignition con-
On
trolled unlock
4
Doorlock out-
0.8 sec.
put duration
5
Double pulse
Off
unlock
6
Double pulse
Off
lock
7
Factory Alarm
with unlock
Disarm func-
tion
8
Factory Alarm
Single
Disarm Pulses
9
Comfort*
Comfort
Closure
Closure 1
10
Panic*
On
*Option not available on 1- button
Menu 2
Feature #
Feature
Opt. 1
1
Engine check-
Virtual tach
ing
2
Engine
12 min
Runtime
3
Park light
Pulsed
output
4
Cranking time
0.6 sec.
5
Activation
1 pulse
pulse count
6
2nd Ignition
Ignition
behavior
7
Accessory
Off during
Options
output
wait-to-start
8
2nd Status
Normal
1-60 min.
behavior
Timed
9
Anti-grind
On
1-90 sec.
0 to 1 second in 50 millisecond
10
Diesel start
Off
increments
delay
Locked
11
Timer mode-
12 min
run time *
Locked
*Option not available on 1- button
Remote Programming
1.
Turn key to the ON position
2.
Within 10 seconds, press and release Valet button one time.
3.
Within 10 seconds, press and hold the Valet button. The LED will flash one time and the horn honks (if con-
nected) to confirm entry into remote programming. Do not release the valet button.
4.
Press the button on the remote control. The horn honks to confirm the remote has been programmed.
Opt. 2
Opt. 3
Opt.4
Opt. 5+
5.
Release the Valet button.
6.
Turn the key to the Off position. The horn sounds one long honk to confirm that remote programming has
Siren
Siren
Siren
Siren
been exited.
20 mS
30 mS
40 mS
50 mS
Off
The programming routine exits if any of the following occurs:
•
The ignition is turned off
•
There is no activity for 30 seconds
Off
•
The Valet button is pressed too many times
3.5 sec.
0.4 sec.
Basic Remote Functions
On
On
Before unlock
Remote start
only
Double
Off
Comfort
Closure 2
Reset and Deletion
Off
If a feature/virtual tach needs to be reset or the remote controls need to be deleted, use the following procedure.
1.
Turn the ignition to the ON position (The heavy gauge pink wire must be connected).
2.
Within 10 seconds, press and release the Valet button: 2 times if you want to delete remotes, 3 times to
reset features or 4 times to reset virtual tach. These features are described next.
Opt. 2
Opt. 3
Opt.4
Opt. 5+
voltage
Off
tachometer
24 min
60 min
Constant
0.8 sec.
1.0 sec.
1.2 sec.
1.4,
1.6,
1.8,
2.0,
4.0 sec
3.
Once you have selected the function step, press the Valet button once more and hold it. The LED flashes and
2 pulses
3 pulses
the horn honks to confirm the selected functional step. Do not release the Valet button.
4.
While holding the Valet button, press the button on the remote control. The horn honks to confirm that the
feature has been successfully reset. You can now release the Valet button.
Accessory
On during
wait-to-start
Latch rear
Pulse rear
defogger
defogger
Off
Timed 15 sec
Timed 30 sec. Timed 45 sec.
3 min
6 min
9 min
Button Press
Function when remote
Function when remote
start is OFF
start is ON
Press for less than 1.5 seconds
Start the engine
Unlock doors
Press for more than 1.5 seconds
Car finder
Stop the engine
Delete remotes: This feature erases all remotes from the memory of the system. This is useful in cases
when a customer's remote is lost or stolen.
Note: This does not reset the programmed features of the system or reset the Virtual Tach setting.
Reset Features: This resets all features of the system to the factory default settings.
Note: This feature does not delete the remotes from the system or reset the Virtual Tach setting
Virtual Tach Reset: Deletes all previously learned values for Virtual Tach, and on the next remote start
sequence the unit begins virtual tach initialization.
Note: The "Zap" feature on the Bitwriter does not reset the Virtual tach setting.
Additional information can be
found at: www.directechs.com
QRN4115V 2012-09
2