Zanussi ZES3921 Manuel de l'utilisateur - Page 18

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Zanussi ZES3921. Zanussi ZES3921 40 pages. Product manaul
Également pour Zanussi ZES3921 : Manuel de l'utilisateur (44 pages)

Imprimer la page

Installation

Warning! Read and follow the instructions carefully.

There is a risk of injury or damage to the appliance.

• Make sure that the appliance is not damaged because

of transportation. Do not connect a damaged appliance.

If it is necessary, speak to the supplier.

• Installation and connection of the appliance to the

power supply must only be done by qualified person-

nel.

• Only use built-in appliances after you assemble the ap-

pliance into correct built-in units and work surfaces

that obey the standards.

• Do not change the specifications or modify this prod-

uct. There is a risk of injury or damage to the appli-

ance.

• Fully obey the laws, ordinances, directives and stand-

ards in force in the country where you use the appli-

ance (safety regulations, recycling regulations, electri-

cal safety rules etc.).

• Keep the minimum distances to other appliances and

units.

• Install anti-shock protection, for example install the

drawers only with a protective panel directly below the

appliance.

• If the fixing bracket is near to the terminal block, al-

ways make sure the connection cable does not come in

contact with the edge of the bracket.

• Prevent damage of the cut surfaces of the worktop

against moisture with a correct sealant!

• Seal the appliance to the worktop with no space left

with a correct sealant.

• Prevent damage of the bottom of the appliance from

steam and moisture, e.g. from a dishwasher or oven.

• Do not install the appliance adjacent to doors and be-

low windows. Hot cookware can be hit off the hob

when you open doors or windows.

• Disconnect the appliance from the electrical supply,

before you do maintenance work or cleaning.

Warning! Risk of injury from electrical current.

Carefully obey the instructions for electrical

connections.

• The electrical mains terminal is live.

• Make the electrical mains terminal free of voltage.

• Install correctly to give anti-shock protection.

• Loose and incorrect mains plug and socket connec-

tions can make the terminal become too hot.

• A qualified electrician must install the clamping con-

nections correctly.

• Use a strain relief clamp on cable.

• Use the correct mains connection cable and replace the

damaged mains cable with the proper cable type.

Speak to your local Service Centre.

The appliance must have the electrical installation which

lets you disconnect the appliance from the mains at all

poles with a contact opening width of minimum 3 mm.

You must have correct isolation devices: line protecting

cut-outs, fuses (screw type fuses removed from the hold-

er), ground leakage trips and contactors.

The manufacturer is not responsible for any injury to per-

sons and pets or damage to property caused by failure to

obey these requirements.

Electrical connection

• Ground the appliance according to safety precautions.

• Make sure that the rated voltage and type of power on

the rating plate agree with the voltage and the power of

the local power supply.

• This appliance is supplied with a mains cable. It has to

be supplied with a correct plug, able to support the

load marked on the rating plate. The plug has to be fit-

ted in a correct socket.

• Any electrical component must be installed or replaced

by the Service Force Centre technician or qualified

service personnel.

• Always use a correctly installed shockproof socket.

• Make sure that there is an access to the mains plug af-

ter installation.

• Do not pull the mains cable to disconnect the appli-

ance. Always pull the mains plug.

• The appliance must not be connected with an extension

cable, an adapter or a multiple connection (risk of fire).

Check that the ground connection is in conformity with

the standard and regulations force.

• The power cable must be placed in such a way that it

does not touch any hot part.