Directed XpressKit DBALL Manuel - Page 8

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Directed XpressKit DBALL. Directed XpressKit DBALL 14 pages. Ford5 remote start ready (rsr) installation
Également pour Directed XpressKit DBALL : Manuel d'installation (16 pages), Manuel d'installation (16 pages), Manuel (19 pages)

Imprimer la page

Platform: DBALL/DBALL2

Firmware: FORD5 Range Extender Ready (RXT) Installation

Feature & Option List

It is recommended to configure all the features and options listed below using the configuration tool found on the module

flashing page on www.directechs.com. The web offers more options such as RXT; however, manual configuration of the

features is possible using the information on this page.

* Default Option

Feat.

Operation

Flashes/Options

1. No RF Output*

RFTD Output

2. RFTD Output

Type

3. SmartStart

1. Disabled

2. Safelock

Smart OEM

Alarm Control

3. Enabled*

Feature Programming

To enter feature programming routine

Turn the ignition ON, then OFF.

Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the

Programming button.

The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate

the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat

until a new command is entered.

Changing feature options

Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature.

The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly

the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.

Accessing another feature

Press and release the programming button a number of times to advance from the current feature to the next desired feature.

The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to

indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.

When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.

Once a feature is programmed

Other features can be programmed.

The feature programming can be exited.

Exiting feature programming

No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming

sequence.

Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the

end of the programming sequence.

Module is connected to a remote starter using a standard installation.

Module is connected to an XL202 using an RSR or RXT installation (when available).

Module is connected to SmartStart using an RSR or RXT installation (when available).

The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm

command will be executed at the beginning or end of the sequence; it must be controlled by

the Remote Starter.

Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It

will unlock at the beginning of the sequence, and relock after start and shutdown.

Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm

the vehicle in the remote start sequence, only when required. The reason for this is, factory

alarm control must often be done by lock or unlock operation. This could create unnecessary

actions on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm

Control will monitor the alarm and door lock status to detect if the disarm or rearm is required.

If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm will not be

executed. Smart OEM Alarm Control will also monitor the remote starter actions so that the

factory alarm control is not done twice. A remote starter, for which the Safelock feature is active,

will work perfectly with this option and will make it invisible to the user.

Description

Programming

Button

Rev.: 20160317

Page 8