Directed Xpresskit DBALL2 Manuel d'installation - Page 6

Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 14 pages. Ford5 remote start ready (rsr) installation
Également pour Directed Xpresskit DBALL2 : Manuel d'installation (12 pages), Manuel d'installation (19 pages), Manuel d'installation (18 pages), Manuel (14 pages), Manuel d'installation (13 pages), Manuel d'installation (19 pages), Manuel d'installation (16 pages), Manuel d'installation (20 pages), Manuel d'installation (15 pages), Manuel d'installation et de référence rapide (16 pages), Manuel d'installation (18 pages), Manuel d'installation (16 pages), Manuel d'installation (18 pages), Manuel d'installation (16 pages), Manuel (19 pages)

Imprimer la page
Directed Xpresskit DBALL2 Manuel d'installation
Platform: DBALL/DBALL2
Firmware:
CHRYSLER6 Range Extender Ready (RXT) Installation

Module Programming

Refer to the LED Diagnostics section for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and
function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest
version of the application.
Warning!
To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit
available functions and features.
1. Connect the interface module to your computer using the XKLoader.
2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware
that is currently saved on the interface module will be indicated in the top right corner of the page.
3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.
4. In the search result page, select Config for RXT, and follow the instructions provided on the screen.
5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.
6. The following message will be displayed when the upload is completed:
"The flashing is successfully completed. You may now unplug the kit."
You can now proceed with the programming instructions below.
SmartStart Installation
The DBALL module must be disconnected from any power source before SmartStart can
be connected to it. Failing to do so could damage DBALL.
a.
To
ensure that the D2D communication between SmartStart and DBALL works properly, the
Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue
loop must be cut (Rev A SmartStart).
b.
Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by
the DBALL D2D connector.
Connect SmartStart to DBALL using the D2D port.
OR
XL202 Installation
Connect XL202 to DBALL using the D2D port.
Connect the 10-pin, 12-pin and 14-pin harnesses to
1
DBALL, then wait until the LED turns ON solid red.
Press 5 times on the programming button.
2
The LED flashes orange.
Turn the key to ignition position. The LED will
3
turn solid orange for 3 seconds then OFF.
You have successfully completed the module programming sequence.
SmartStart
rd
3
st
1
nd
2
Press x5
Key IN
Rev.: 20150827
Page 6
XL202
&
Solid
&
Flashes
&
START
Solid x3 sec.
© 2015 Directed. All rights reserved.