Alecto ADB-19 Manuel d'installation

Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} Alecto ADB-19. Alecto ADB-19 2 pages.
Également pour Alecto ADB-19 : Installation (2 pages), Installation (2 pages), Manuel de démarrage rapide (2 pages)

Imprimer la page
Transmitter Installation:
Transmitter Installation:
● Stick the Transmitter on the wall or the door with
● Stick the Transmitter on the wall or the door with
ADB-19 Installation
double-sided adhesive tape.
double-sided adhesive tape.
Battery Installation (Transmitter):
Receiver Installation:
Receiver Installation:
Indoor-unit:
Transmitter uses a 3V CR2032 battery (included).
● Plug the Receiver into any socket of AC110~240V power.
● Plug the Receiver into any socket of AC110~240V power.
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.
attery Installation (Transmitter):
ransmitter uses a 3V CR2032 battery (included).
pen the Transmitter (by pushing in the interface located at the bottom with a flat screw dri
Auto-leaning Code Wireless Door Chime
nd place the battery. Please be well noted with the correct battery polarity. To replace a new
Outdoor-unit:
Auto-leaning Code Wireless Door Chime
attery, operate in the same way.
Accessories List:
Important Note:
● 1 x Receiver
Accessories List:
● 1 x User Manual
● If you do not plan to use the device for a long time, such as at a vacation, please remove the
● 1 x 3 volts CR2032 battery for transmitter
● 1 x Receiver
battery from Transmitter, then put them in a safe place.
● 1 x User Manual
● Improperly using a battery may cause it to leak and damage nearby items, and can create the
● 1 x 3 volts CR2032 battery for transmitter
Technical Specification:
● Frequency: 433.92MHz+100KHz
risk of fire and personal injury. Batteries should not be left in an area where the children can
● Modulation Type: ASK
Technical Specification:
reach them as they may pose a chocking hazard.
● Ring Volume:＞85dB(within 0.5m)
● Frequency: 433.92MHz+100KHz
● Channel space: 1 million sets of auto-learning codes
● Recycle used batteries following environmental protection practices.
● Modulation Type: ASK
● Receiver bandwidth: ±90KHz
● Ring Volume:＞85dB(within 0.5m)
● Reception Sensitivity:＞-105dBm
● Channel space: 1 million sets of auto-learning codes
● Transmitter Power:＜10mW
● Receiver bandwidth: ±90KHz
● Power consumption(Receiver): standby:＜0.3W
● Reception Sensitivity:＞-105dBm
Transmitter Installation:
● Power consumption(Transmitter): standby:＜5uA working:＜10mA
● Transmitter Power:＜10mW
● Power Supply(Receiver): AC110-240V
● Stick the Transmitter on the wall or the door with
● Power consumption(Receiver): standby:＜0.3W
● Power Supply(Transmitter): DC 3V (1x CR2032)
● Power consumption(Transmitter): standby:＜5uA working:＜10mA
double-sided adhesive tape.
● Operating Range:＞150m (in the open air)
● Power Supply(Receiver): AC110-240V
● Power Supply(Transmitter): DC 3V (1x CR2032)
Names for Parts:
● Operating Range:＞150m (in the open air)
Receiver Installation:
mportant Note:
● Plug the Receiver into any socket of AC110~240V power.
Connecting:
Names for Parts:
If you do not plan to use the device for a long time, such as at a vacation, please remove th
1x
1x
battery from Transmitter, then put them in a safe place.
Improperly using a battery may cause it to leak and damage nearby items, and can create t
CODE
risk of fire and personal injury. Batteries should not be left in an area where the children ca
MODE
reach them as they may pose a chocking hazard.
CODE
VOL
MODE
Recycle used batteries following environmental protection practices.
VOL
ransmitter Installation:
Stick the Transmitter on the wall or the door with
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Instruction Manual
Open the Transmitter (by pushing in the interface located at the botto
Instruction Manual
and place the battery. Please be well noted with the correct battery po
Model No.: QH-861AK
battery, operate in the same way.
Model No.: QH-861AK
● 1 x Transmitter
● 1 x Double-sided adhesive
Important Note:
● If you do not plan to use the device for a long time, such as at a vaca
battery from Transmitter, then put them in a safe place.
● Improperly using a battery may cause it to leak and damage nearby
risk of fire and personal injury. Batteries should not be left in an area
reach them as they may pose a chocking hazard.
<10 sec.
● Recycle used batteries following environmental protection practice
1x
1
Transmitter Installation:
1
● Stick the Transmitter on the wall or the door with
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface
and place the battery. Please be well noted with t
2
2
battery, operate in the same way.
● 1 x Transmitter
● 1 x Double-sided adhesive
Important Note:
● If you do not plan to use the device for a long t
battery from Transmitter, then put them in a sa
● Improperly using a battery may cause it to leak
risk of fire and personal injury. Batteries should
reach them as they may pose a chocking hazar
● Recycle used batteries following environmenta
Transmitter Installation:
2
● Stick the Transmitter on the wall or the door wi
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
Press lightly the battery
holder at side
Accessories List:
● 1 x Receiver
● 1 x User Manual
CR2032 3V Lithium Battery
● 1 x 3 volts CR2032 battery for transmitter
Technical Specification:
● Frequency: 433.92MHz+100KHz
● Modulation Type: ASK
● Ring Volume:＞85dB(within 0.5m)
● Channel space: 1 million sets of auto-learning co
● Receiver bandwidth: ±90KHz
● Reception Sensitivity:＞-105dBm
● Transmitter Power:＜10mW
● Power consumption(Receiver): standby:＜0.3W
● Power consumption(Transmitter): standby:＜5u
● Power Supply(Receiver): AC110-240V
● Power Supply(Transmitter): DC 3V (1x CR2032)
● Operating Range:＞150m (in the open air)
Unregister
Names for Parts:
1x
Press
Instruction
holde
Auto-leaning Code W
Model No.: Q
CR2032
CODE
MODE
5 sec.
VOL