Directed Electronics SMARTSTART DSM200 Référence rapide Manuel d'installation - Page 2
Parcourez en ligne ou téléchargez le pdf Référence rapide Manuel d'installation pour {nom_de_la_catégorie} Directed Electronics SMARTSTART DSM200. Directed Electronics SMARTSTART DSM200 2 pages.
Imprimer la page
tion in the following wiring diagram and steps
(Note CAUTIONS during installation).
a. Complete the main power connections.
b. Connect the 4-pin extension cable to the
SmartStart module cable.
c. Connect the interface cable to the extension
cable and the other appropriate end into the
Bitwriter port of the Directed system.
d. When power is connected, the module be-
gins an initialization procedure that may
take several minutes. During this procedure,
progress is reported via the flashing Amber/
Green LEDs next to the module cable. When
both LEDs turn on solid, the initialization pro-
cedure is completed (See Status LEDs for a
description of the various LED states).
Note: If the system does not include a remote control,
skip step 4 and proceed to step 5.
4. Re-verify security/remote start system operation:
Perform all basic operations such as Lock, Unlock,
Panic and Remote Start, (Trunk release where ap-
plicable) using the supplied remote control. If the
system operates as expected proceed to the next
step (5). If the system does not operate as ex-
pected, rectify the problem first.
5. Verify and Activate the VSM200/DSM200:
The following steps need to be performed for the
Verification/Activation of the VSM200/DSM200
Directed SmartStart module.
a. Collect Customer Information:
Customer's Full Name:
Customer's E-mail Address:
Record/place Module ID # here:
New Account:
If this is an existing account, are you:
adding a new system:
or replacing an existing one:
Additional information can be
found at: www.directechs.com
2
Existing Account:
b. Log on to: www.directed.com/SmartStart
and click on the "Activate Your System" but-
ton.
c. From the SmartStart Activate screen click on
the Installer link.
d. Enter name and password into fields and log
in.
e. Select and click on the appropriate "device"
button. Fill in fields and follow the onscreen
prompts.
f.
Select brand of installed system from the
drop-down menu.
g. Test the SmartStart system from the website
using the supplied function links.
h. The customer is sent log-in information for
the new Customer Service Portal via e-mail.
From there, they must provide the required
information. Once completed, the installed
system and account are activated. The cus-
tomer can then open the phone app and be-
gin using the service.
Status LEDs
Amber LED states:
•
Off: No cellular communication. Check
connections such as module harness.
•
Flashing slowly: The module is seeking
cellular system communication.
If no cell coverage is available the Amber
LED continues to flash slowly, move the
vehicle to a location with better reception.
•
Flashing quickly: The module is negotiat-
ing with a cellular system.
•
On solid: Communication successfully es-
tablished.
Green LED states:
•
Off: Communication not established with
the remote start main unit.
Check connection at the Bitwriter port,
once connected properly the LED turns
on.
•
Flashing: Active communication in prog-
ress between the SmartStart module and
Remote Start main unit.
•
On solid: Communication successfully es-
tablished with the remote start main unit.
Please return this guide and point the customer to
step 5h after successfully completing the installation
as it contains details required for account setup.
Notes: SmartStart response time can vary depend-
ing on cellular coverage and network congestion.
Operating temperature range: -30°C to + 70°C.
Directed Logo Usage
Logo, Directed with designed in USA.eps
© 2010 Directed Electronics. All rights reserved.
Logo, Directed Electronics w-driven.eps