Acorn HFI-DPT-05 Manuel de démarrage rapide - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} Acorn HFI-DPT-05. Acorn HFI-DPT-05 2 pages. Programming unit

Imprimer la page

IDENTIFIYNG THE DEVICE

Under the DevType and Addr captions on the programming unit's display, the connected analogue devices are visualized as per the follow-

ing table:

Device's type indication

Refers to...

Photo

Analogue and enhanced conventional smoke detector

PhtTherm

Analogue and enhanced conventional smoke and thermal detector

Thermal

Analogue and enhanced conventional thermal detector

I Module

Analogue input module or channel

O Module

Analogue relay output module or channel

OModSup

Analogue supervised output module or channel

Analogue multiple input / output channels device or analogue multi-

Multiple

module

CallPnt

Analogue call point

Sounder

Analogue sounder (wall or base)

Beacon

Analogue beacon

Sound B

Analogue sounder beacon

Conv Zon

Conventional zone module

Remote I

Analogue remote indicator lamp

Special

An analogue device that is not in this list

SETTING THE THERMAL OPERATING MODE

Having a detector with a thermal sensing feature connected to the programming unit, while visualizing ThrTyp on the main menu, press the

WRITE key: SelTyp (select type) caption will be displayed, and under it will be indicated either Std (standard ROR mode) or High°C (high

temperature mode) depending on the actual thermal operating mode of the detector; if you want to change the thermal mode just press UP

or DOWN to select the desired one, then press the WRITE key.

You can return to the main menu, if you decided not to change nothing, by pressing on the READ key.

SETTING THE OPERATING MODE VALUE

While in Set Mod / Set Op press the WRITE key. The Sel Op sub-menu and caption will appear on display: beneath it, three digits will

indicate the actual programmed operating mode value for the connected device that can be changed by pressing the UP or DOWN keys;

after the value has been chosen, just press WRITE to memorize it on the connected device.

You can return to the main menu, if you decided not to change nothing, by pressing on the READ key.

MESSAGES

The following table illustrates the most common messages given by the programming unit and their meaning:

Programming unit message

Meaning

Ent Test

This message is given when the enter test, made for the enhanced conven-

Error!

tional detector, failed

Ent Test

This message is given when the enter test, made for the enhanced conven-

tional detector, succeeded

An irreversible error; if this occurs, the detector is compromised, must not be

Fatal Error!

used and needs to be substituted

Storing

Indicates that the device is being programmed with the selected parameter

Indicates that the device has been successfully programmed with the selected

Stored

parameter

Reading

Indicates that the device is being queried for a parameter value

Read

Indicates that the device has been successfully queried for a parameter value

Failed

The performed reading or storing operation just failed

Miss Dev

No device is connected to the programming unit

BlankDev

The connected device has no firmware programmed

No Addr

The connected device has no analogue address

Low batt

Programming unit battery needs to be changed

Unspec

Customer security code is not specified

POWER OFF

The programming unit switches off by itself after 30 seconds of inactivity.

TECHNICAL SPECIFICATIONS

Power supply battery specifications

6LR61 type, 9 V

Operating temperature range

from -30°C to +70°C

Maximum tolerated relative humidity

95% RH (no condensation)

Weight

200 grams

WARNINGS AND LIMITATIONS

Our devices use high quality electronic components and plastic materials that are highly resistant to environmental deterioration. However,

after 10 years of continuous operation, it is advisable to replace the devices in order to minimize the risk of reduced performance caused by

external factors. Ensure that this device is only used with compatible control panels. Detection systems must be checked, serviced and

maintained on a regular basis to confirm correct operation.

Smoke sensors may respond differently to various kinds of smoke particles, thus application advice should be sought for special risks.

Sensors cannot respond correctly if barriers exist between them and the fire location and may be affected by special environmental condi-

tions.

Refer to and follow national codes of practice and other internationally recognized fire engineering standards.

Appropriate risk assessment should be carried out initially to determine correct design criteria and updated periodically.

WARRANTY

All devices are supplied with the benefit of a limited 3 year warranty relating to faulty materials or manufacturing defects, effective from the

production date indicated on each product.

This warranty is invalidated by mechanical or electrical damage caused in the field by incorrect handling or usage.

Product must be returned via your authorized supplier for repair or replacement together with full information on any problem identified.

Full details on our warranty and product return policy can be obtained upon request.