CTS MCT-5002SFP+ Manuel de l'utilisateur
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} CTS MCT-5002SFP+. CTS MCT-5002SFP+ 2 pages. 100m/1g/2.5g/5g/10g nbase-t to 10gbase-r standalone media converter
Imprimer la page
Trademarks
CTS is a registered trademark of Connection Technology
Systems Inc. Contents subject to revision without prior notice.
All other trademarks remain the property of their owners.
Copyright Statement
Copyright Connection Technology Systems Inc.
This publication may not be reproduced as a whole or in part, in
any way whatsoever unless prior consent has been obtained
from Connection Technology Systems Inc.
FCC Warning
This equipment has been tested and found to comply with the
limits for a Class-A digital device, pursuant to Part 15 of the
FCC Rules. These standards are designed to provide
reasonable protection against harmful interference when these
devices are operated in a commercial environment. These
devices generate, use, and can radiate radio frequency energy
and may cause harmful interference to radio communications
unless installed in accordance with this User's Guide.
Operation of these devices in a residential area is likely to
cause harmful interference which will make the user
responsible for the appropriate remedial action at his / her own
expense.
CE Mark Warning
These are Class A products. In a domestic environment these
products may cause radio interference in which case the user
will need to consider adequate preventative methods.
1. Checklist
The package should contain the following items:
- One set of MCT-5002SFP+ Media Converter
- 1X AC-DC Power Adapter
- This User's Guide
Please notify your sales representative immediately if any
items are missing or damaged.
2. Overview
MCT-5002SFP+, a compact media converter, converts
traditional twisted-pair RJ-45 cable with 10G NBase-T
technology into a 10G SFP+ slot for pluggable fiber transceiver,
extending transmission distance for Data Center 10G NBase-T
to 10GBase-R conversion application or ISP Mobile DU (Dis-
tributed Unit) and Enterprise broadband service applications.
MCT-5002SFP+ media converter is fully compliant with 802.3u,
802.3ab, 802.3z, 802.3bz, 802.3ae, and 802.3an standards.
Operation status can be locally monitored through a set of
Diagnostic LEDs located in the front panel.
Major Features:
- Support Auto-Negotiation for 5-speed options (100M/
1G/2.5G/5G/10G) in TP port
- Up to 10G at 100m over Cat.6A cable or better cabling, or
2.5G at 100m over Cat.5E or better cabling. (For more
details, please see Section 7.)
- Support MDI/MDI-X Auto-Crossover
- Support Link Alarm
- Support Jumbo Frame 9K bytes (under 10Gbps)
- Support the loopback mode in the fiber port
- Support the fully-transparent mode
- Support Auto & Force mode configuration for the TP port.
- Fully compatible with CTS MCT-RACK-12/18-MGM chassis
for in-rack management
3. Installation
- Attach the fiber cable from MCT-5002SFP+ to the fiber
network. The fiber connections must be matched – transmit
socket to receive socket.
- Attach a UTP cable from the NBase-T network to the RJ-45
port on MCT-5002SFP+.
- Connect the power adapter to the power jack on the rear
panel of MCT-5002SFP+ and check that if the Power LED
lights up. The TP and F/O LEDs will light up when all the
cable connections are satisfactory.
Fig 1. Side View of MCT-
5002SFP+ Converter
DIP
RJ-45
Switch
Port
Fiber
Port
Fig 2. Rear Panel of MCT-5002SFP+ Converter
CAUTION
To prevent suffering from burns due to the high
temperature, please wear a protective equipment
when you install or remove especially the converters.
4. LED Description
LED
Color
Function
Power
Green
Lit when power is available.
OFF
TP port link is down.
Lit when TP 10Gbps port link is up.
Green
Blinking when TP port is receiving and
transmitting data at the speed of 10Gbps.
TP
Lit when TP port link less than 10Gbps is
up.
Orange
Blinking when TP port is receiving and
transmitting data at the speed of less than
10Gbps.
OFF
Fiber port link is down.
Lit when Fiber 10Gbps port link is up.
F/O
Green
Blinking when Fiber port is receiving and
transmitting data at the speed of 10Gbps.
OFF
TP works in the half-duplex mode.
FDX
Lit when TP works in the full-duplex
Green
mode.
Lit when the converter module is in
Green
normal operation.
Lit when the system is booting up.
Slowly blinking when the firmware of the
converter module is not compatible with
CTS MCT-RACK-MGM chassis. The
Orange
Status
converter module needs to be upgraded
with the new firmware.
Rapidly blinking when the converter
module works abnormally.
Orange
Slowly blinking when the system is
upgrading the firmware.
Green