Nikon SB-102 os Manuel d'instruction - Page 7
Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Nikon SB-102 os. Nikon SB-102 os 36 pages. Speedlight
Imprimer la page
TIPS ON SPEEDLIGHT CARE
1.
After using the
speedlight
and camera under-
water, rinse them both as soon as possible in
fresh running water
with the sync and sensor
cords
attached. When the
speedlightlcamera
assembly gets
dirty,
rinse
it thoroughly in
fresh
water.
Immediately
after
using
it in salt
water,
rinse it thoroughly in fresh water
to
remove
any
residue.
Otherwise,
corrosion
may occur in
minute places like
small
holes or the junctions
of parts. To prevent
this,
soak
the
speedlightl
camera assembly overnight in a basin of fresh
water, then rinse it vigorously in running water
while paying special attention to the joint
@,
arm
@,
bracketscrew
@,buckles
®,
andsimilarparts
where it
is
very difficult to remove mud or
salt.
Finally, dry the
speedlight/camera
assembly with
a soft
cloth-never by
heating-before
removing
the sync
and sensor cords.
Be
sure
to wipe away
any drops of water that may have
speeded
in
past the O·ring.
When the unit is
completely
dry,
check
the
a-rings.
If
any
of them is
scratched
or damaged,
immediately replace it
with a
new
one
by follow-
ing
the procedures
in "
PREPARATION
."
All moving parts
should be
lubricated to prevent
corrosion and
facilitate
attachment.
Apply lubri-
cant sparingly and be sure
to wipe off
any excess.
When
the speedlight
will not be used
for some
time
,
store
it in
a cool
, dry,
clean
place
with
the
batteries
and
battery
chamber cap
removed
.
2.
Never submerge
the
speedlight in water with
the sync or sensor socket cover removed
,
or
get the sync or sensor cord plugs wet.
Always
make
sure
the
sync cord and sensor cord
plugs
are
securely attached
before
entering
the
water.
3.
Never pick up or
suspend the speedlight
by the
sync or sensor cords.
4.
If
an O-ring
with
dust,
scratches, or
damage is
used,
water may
enter
the flash unit
and
damage
the
electrical circuitry.
Before
and after
diving,
check the
O-rings by following the procedures
in
"PREPARATION
."
5.
Do not
allow
the
speedl ight
to be
exposed
to
direct
sunlight
for long
periods.
And never place
the
speedlight in an
area
where
the
temperature
is or may
rise
to
60°C (140°
F)
such as
in
a
closed car or car trunk during w'arm weather.
6.
High-voltage
circuitry
may
cause electrical
shock
if
water enters
the flash unit. Should
water
get
inside
the
flash
unit,
take
it-with
the bat,
teries
and
battery
chamber cap
removed-to
an
authorized Nikon dealer
or service center
immediately.
If
you experience
difficulty
of an electrical
nature
with
the
unit,
never
attempt
to disassemble or
service it
yourself.
Instead, take the unit to
an
authorized
Nikon dealer or
service center.
7.
As much
as
possible,
avoid
removing the battery
chamber cap
near
salty
wind or
splash
ing water
because
either may
damage
the
unit's
electrical
circuitry.
If
the
battery
chamber cap
must be
removed in one of these
situations,
for instance,
to
exchange
batteries, use a vinyl bag to prevent
water
or salt
from
entering
the unit.
8.
When not using
the speedlight
,
remove batteries
to prevent damage from battery
leakage.
Leaking
batteries may
also cause
dangerous combustible
gases
to be trapped inside the battery
chamber.
If the battery
chamber
becomes corroded by
leakage,
take the unit to
an authorized
Nikon
dealer
or
service center.
9.
To remove dirt or fingerprints
,
wipe with a soft,
dry or
silicon,treated cloth.
Never use
thinner,
benzine, or alcohol because they may damage
plastic parts. To clean the Wide-Flash Adapter
SW-102, wash it with soap and water. Never
use a brush
.
10.
If this
speedlight
is frequently used underwater
(especially
in
salt
water or dirty
water),
take it to
an authorized
Nikon dealer or
service center
for
inspection
on
a
regular
basis.
11
.
If the
speedlight
is dropped or bumped
against
a
hard
surface,
take it to an authorized Nikon
dealer or service center
for inspection even if
there is no
surface
damage.
12.
After using the
speedlight
,
attach
the dust-proof
plastic
caps
to the
sync and sensor
cord plugs
to protect them from damage.
I
."
.
.
............
I
7