Blade 360 CFX 3S Manuel d'instruction - Page 4
Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Blade 360 CFX 3S. Blade 360 CFX 3S 15 pages.
Imprimer la page
First Flight Preparation
• Remove and inspect contents
• Begin charging the fl ight battery
• Install the fl ight battery in the helicopter (once it has been fully charged)
• Program your computer transmitter
• Bind your transmitter
• Familiarize yourself with the controls
• Find a suitable area for fl ying
Low Voltage Cutoff (LVC)
The ESC will continuously lower power to the motor until complete shutdown
when the battery reaches 18V under load. This helps prevent over-discharge of the
Li-Po battery. Land immediately when the ESC activates LVC. Continuing to fl y after
LVC can damage the battery, cause a crash or both. Crash damage and batteries
damaged due to over-discharge are not covered under warranty.
Transmitter Setup
Program your transmitter before attempting to bind or fl y the helicopter.
Transmitter programming values are shown below for the Spektrum DX6i,
DX7/DX7se, DX6, DX7s, DX8, DX9 and DX18.
DX6i
SETUP LIST
ADJUST LIST
Model Type
Thro Curve
HELI
NORM
STUNT
Reverse
HOLD
THRO N
AILE
R
Pitc Curve
NORM
ELEV
R
STUNT
RUDD R
GYRO N
HOLD
PITC
N
Travel Adj
THRO
Low: 100% Hi: 110%
Swash Type
1 Servo 90
AILE
ELEV
Timer
RUDD
3:00
GYRO
PITC
EN
0%
30%
30%
30%
30%
100% 100% 100% 100% 100%
0%
0%
0%
0%
0%
30%
40%
50%
75%
100%
0%
25%
50%
75%
100%
0%
25%
50%
75%
100%
100%
Gyro
100%
Rate
SW-F. Mode
100%
NORM
20%
100%
STUNT
20%
100%
DX6/DX7s/DX8/DX9/DX18
SYSTEM SETUP
FUNCTION LIST
D/R & Expo
Model Type
0-AILE
HELI
0-ELEV
Swash Type
0-RUDD
1 Servo Normal
1-AILE
F-Mode Setup
1-ELEV
Flight Mode: F Mode
1-RUDD
Hold: Hold
2-AILE
Frame Rate
2-ELEV
22ms
2-RUDD
DSMX
SERVO SETUP
Travel
THRO
Low: 130% Hi: 110%
AILE
ELEV
RUDD
GEAR
PIT.
Flying Checklist
❏ Always turn the transmitter on fi rst
❏ Plug the fl ight battery into the lead from the ESC
❏ Allow the ESC to initialize and arm properly
❏ Fly the model
❏ Land the model
❏ Unplug the fl ight battery from the ESC
❏ Always turn the transmitter off last
Repeatedly fl ying the helicopter until LVC activates will damage the helicopter
battery.
Disconnect and remove the Li-Po battery from the aircraft after use to prevent
trickle discharge. During storage, make sure battery charge does not fall below
3V per cell.
The fi les for models using Spektrum™ transmitters with AirWare™ software are
also available for download online at www.spektrumrc.com.
DX7/DX7se
SYSTEM LIST
Model Type
HELI
Swatch Type
1 Servo 90
Throttle Curve
100%
0%
NORM
0%
100%
0%
ST-1
75%
100%
0%
ST-2 (DX6, 8, 9, 18) 100% 100% 100% 100% 100%
85%
0%
HOLD
0%
85%
0%
Pitch Curve
85%
0%
NOR
30%
85%
0%
ST-1
0%
85%
0%
ST-2 (DX6, 8, 9, 18) 0%
85%
0%
HOLD
0%
Reverse
THRO
N
AILE
R
100%
ELEV
R
100%
RUDD
R
100%
GEAR
N
100%
PIT.
R
100%
4
FUNCTION MODE
D/R & EXP
0-AILE
100% 0%
0-ELEV
100% 0%
0-RUDD
100% INH
1-AILE
85%
0%
1-ELEV
85%
0%
1-RUDD
85%
INH
Thro Curve
NORM
0%
30%
30%
ST-1
75%
75%
75%
ST-2
100% 100% 100% 100% 100%
HOLD
0%
0%
0%
Pitc Curve
NORM
30%
INH
50%
ST-1
0%
INH
50%
ST-2
0%
INH
50%
HOLD
0%
INH
50%
Travel Adj
Reversing SW
THRO N
THRO
Low: 130% Hi: 110%
AILE
100%
AILE
ELEV
100%
ELEV
RUDD
100%
Gyro SENS
GEAR
100%
AUTO F.MODE
PIT.
100%
STNT 20%
HOLD 20%
30% 30% 30% 30%
75% 75% 75% 75%
0%
0%
0%
0%
40% 50% 75% 100%
25% 50% 75% 100%
25% 50% 75% 100%
25% 50% 75% 100%
Timer
MODE
Countdown
TIME
3:00 Tone/Vibe
START
Throttle Cut
POS
25
Gyro
SW
F Mode
CH
Gear
NORMAL/POS 0 58%
STUNT 1/POS 1 48%
STUNT 2/POS 2 40%
HOLD
58%
30%
30%
75%
75%
0%
0%
INH
100%
INH
100%
INH
100%
INH
100%
RUDD R
R
GEAR N
R
PIT.
R
Timer
3:00