Blade Inductrix200 Manuel d'instruction - Page 10

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Blade Inductrix200. Blade Inductrix200 17 pages.

Imprimer la page

Flight Mode Selection

• In stability low angle mode (quadcopter LED blue), the

controls provide a minimum bank angle.

• In stability high angle mode (quadcopter LED green), the

controls provide a maximum bank angle.

• In agility mode (quadcopter LED red), the system does

not self level. Use rates and expo to tune the perfor-

mance according to your ﬂ ying style.

Refer to the Transmitter Setup Table for transmitter switch

selection and speciﬁ c setup information.

Flying the Inductrix

Consult your local laws and ordinances before choosing a

location to ﬂ y your aircraft.

We recommend ﬂ ying your aircraft outside in calm winds or

inside a large gymnasium. Always avoid ﬂ ying near houses,

trees, wires and buildings. You should also be careful to

avoid ﬂ ying in areas where there are many people, such as

busy parks, schoolyards or soccer ﬁ elds.

When you have located a suitable ﬂ ying site and are ready to ﬂ y:

1. Power on the transmitter.

2. Install the ﬂ ight battery into the quadcopter.

3. Power on the quadcopter by pressing the power

button/LED. The LED will glow for approximately

1-2 seconds indicating the battery charge status.

Green = Fully charged.

Yellow = Approximately half full.

Red = Discharged. Do not ﬂ y. Charge the ﬂ ight battery.

Takeoff

With all trims centered and the throttle fully lowered,

start the motors by moving the rudder stick to the right

then back to center. Increase the throttle until the model

is approximately 2 ft. (600mm) off the ground.

Making small corrections on the transmitter, try to hold

the quadcopter in one spot. If ﬂ ying in calm winds, the

model should require almost no corrective inputs. After

moving the cyclic stick and returning it to center the

model should level itself. The model may continue to

move due to inertia. Move the cyclic stick in the opposite

direction to stop the movement.

Do not use the trims on the transmitter to eliminate drift.

If the quadcopter does not hold a reasonable hover in

calm conditions, perform the Drift Calibration.

™

Quadcopter

Flying

With your quadcopter maintaining a stable low-level hover,

practice using the rudder, elevator and aileron controls to

familiarize yourself with the machine's responses to control

inputs. Remember to keep the control inputs as minimal

as possible.

When you are comfortable with basic ﬂ ight you may

explore the different ﬂ ight modes and functions explained

in the Flight Mode Selection section of this manual. The

different ﬂ ight modes are accessed using the controls

programmed in the Transmitter Setup section.

Releasing the sticks in either of the Stability Modes will allow

the quadcopter to level itself. If you become disoriented,

slowly lower the throttle stick to land softly.

Typical ﬂ ight times for the included battery range

from 5-6 minutes.

Low Voltage Cutoff (LVC)

LVC decreases the power to the motors when the bat-

tery voltage gets low. The LED on the quadcopter will

indicate when the battery charge is getting low. When the

quadcopter LED ﬂ ashes red continuously, land the aircraft

immediately and recharge the ﬂ ight battery. Continuing to

ﬂ y after the LED begins to ﬂ ash red will cause the motors

to slow and eventually shut down, causing a crash.

NOTICE: Crash damage is not covered under warranty.

NOTICE: Repeated ﬂ ying to LVC will damage the battery.

LVC does not prevent the battery from over-discharge

during storage.

Landing

To land, slowly decrease the throttle while in a low-level

hover. After landing, activate the motor stop feature, as

described in the Transmitter Setup, to stop the motors.

Press the power button/LED on the quadcopter to power

off. Remove the battery from the aircraft after use to

prevent over discharge. During storage, make sure the

battery charge does not fall below 3V per cell.