Armytek Wizard Manuel de l'utilisateur - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Armytek Wizard. Armytek Wizard 2 pages.

Imprimer la page

Set description

Wizard

Your flashlight can inconsiderably differ from the pictures in the manual.

The producer reserves the right to change the package at his own discretion without modifying this manual.

Initial Service

To set/replace batteries:

1. Unscrew the tailcap.

2. Place the batteries with the positive contact (+) facing the head of the flashlight.

3. Adjust the tailcap and tighten it as far as it can go.

The flashlight is ready for operation.

We DO NOT RECOMMEND to leave power sources inside the flashlight for a long storage period, as batteries (especially, non-rechargeable) can

leak for various reasons and damage the inner parts of the flashlight. If you want to keep your flashlight in a stand-by state with batteries in then use

new and high-quality batteries and store the flashlight in acceptable for batteries operational temperature and revise the batteries' state at least

once a month. If you have noticed any signs of batteries' defects then withdraw them from the flashlight and utilize. It is also recommended to

replace discharged batteries with new ones before the storage as the chance of leakage is higher with discharged batteries.

To use the head mount with the flashlight:

Connect the

small strap

with the

silicone holder.

Fix the

flashlight and

adjust the

elastic bands

to the size

of your

head.

Items included in the package:

1 - Flashlight

2 - Clip

3 - Headband (2 straps)

4 - Silicone holder

5 - 2 spare O-rings

6 - User manual

Pass the ends of the big strap through

the loop of the small strap and slots in

the silicone holder (fig.b), conjoin

them in a ring (fig.c). Pass the loose

end of the big strap through the loop of

the small one in the opposite direction

and fix it in the buckle (fig.e).

In OFF state:

Click: To turn on the last used mode.

Press and hold: To go through 2 Firefly modes (release to select). Keeping button pressed will start cycling through the Main modes.

In ON state:

Click: To turn off the flashlight.

Press and hold: To start cycling through the Main modes.

Double click: To turn on the Turbo mode. The second double click brings back the last used mode.

For comfortable operation you have a convenient momentary access to all the following modes:

Firefly

Press & Hold

OFF вFirefly1 вFirefly2

Click x1

OFF вMain (if last used)

Turbo

Click x2

Any mode вTurbo

Turbo вLast mode

Cycling through Modes

Press & Hold

Main1 вMain2

Main3

Automemorizing. After switching off the last used Mode is memorized for quick 1-click access at next switching on.

Lock-out function. Unscrew the tailcap to 1/4 for the protection from accidental switching on.

Low Battery Indication

Low Battery Indication.

ONCE (after 30sec from switching on). If you are not sure if it flashed or not switch the flashlight

Warning

Critical

off and on: in case the battery is low flashes will repeat. Light output decreases to Firefly mode at

critical level.

Active temperature control. The flashlight can quickly heat up in Turbo mode. When the

temperature become +60°C – the brightness decreases by small steps. After cooling-down

(provided that battery voltage is sufficient) the brightness increases to the Turbo mode again.

This stepping goes cyclically to maintain the user's safety and the flashlight's functionality. In

вFirefly1

conditions of good air-cooling the flashlight delivers light without stepping down even in Turbo

вOFF

mode. There are no preset timers for stepping, but real-time active temperature measurements.

Operation

Firefly. Press and hold the button in OFF-state to turn on the

desired Firefly mode and then release immediately. Keeping

the button pressed will start cycling through the Main

modes.

Main

Main. Short click from OFF-state activates the Main mode (if

it was the last mode used previously).

Turbo. The mode is activated by double click in any mode. To

return to the last mode make double-click again.

Cycling through the Main modes. In ON-state press and hold

the button (in any mode): the 3 Main modes will start

switching cyclically. Release the button to select the desired

mode.

In Turbo mode it starts cycling through the Main

modes.

If the brightness is <25% from the nominal value, the LED flashes 2 times