Armytek Optoelectronics Wizard Pro Manuel de l'utilisateur

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Armytek Optoelectronics Wizard Pro. Armytek Optoelectronics Wizard Pro 2 pages.
Également pour Armytek Optoelectronics Wizard Pro : Manuel de l'utilisateur (2 pages)

Imprimer la page

With ambient temperature +25°C the flashlight delivers light in Maximum mode for about 8-10 minutes and then the brightness steps

down to the Main3 mode. 40-60 seconds afterwards the brightness increases to the Maximum mode again. This stepping goes

cyclically to maintain the user's safety and the flashlight's functionality. In the conditions of good air-cooling the flashlight delivers

constant light even in Maximum mode. It does not use timers, but real active temperature measurements.

1. Always follow the instructions from this manual and recommendations on battery usage.

2. Apply only the recommended power sources.

3. Do not reverse battery polarity.

4. Do not use different power sources together, i.e. old ones with new ones, charged with

discharged. Do not use different types of batteries combined as the element with less

capacity can be damaged.

5. Do not modify or recast the flashlight and its components as it will deprive you of the

warranty.

6. Do not allow water or any other liquid to leak into the flashlight.

7. Do not aim a turned-on flashlight at people's or animals' eyes – it can cause temporary

blindness.

8. Do not allow children to use the flashlight without your assistance.

Armytek Optoelectronics Inc. shall not be liable for any harm done to the user if it

was caused by improper use of the product.

Care and Storage

It is recommended to clean the threads and O-rings off dirt and old grease. Remember that secure protection from water and dust

cannot be provided by worn out sealing. And fouling as well as lack of lubricant cause fast wear-out of threads and sealing rings.

To clean the threads do the following:

1. Unscrew the tailcap and remove the sealing ring carefully with a toothpick (do not use sharp metal things as they can damage the ring).

2. Wipe the sealing ring thoroughly with a soft cloth (or tissue). Do not use solvents. If the sealing ring is worn out or damaged

replace it by a new one.

3. Clean the metal threads with a brush using ethanol. Be careful not to allow applied liquid to get inside the flashlight or tailcap as it

can cause fails in functionality of the flashlight.

After cleaning lubricate the thread and the sealing ring with polyalphaolefin-based silica grease, e.g. Nyogel 760G.The application of

automotive and other improper grease can cause swelling and damage of the sealing rings.

In case of active operation and exploitation in dusty environments, it is recommended to perform cleaning and lubricating of the parts

as often as required, even if it is more than twice a year.

We recommend NOT to leave power sources inside the flashlight for a long storage period, as batteries (especially, non-rechargeable) can leak for

various reasons and damage the inner parts of the flashlight. If you want to keep your flashlight in a stand-by state with batteries in, use new and

quality batteries, store the flashlight in acceptable for batteries operational temperature and revise the batteries' state at least once a month. If you

have noticed any signs of batteries' defects, withdraw them from the flashlight and take out of operation. It is also recommended to replace

discharged batteries with new ones before the storage as the chance of leakage is higher with discharged batteries.

Service and Warranty

Armytek provides free warranty repair for 10 years from the purchase.

Warranty doesn't cover damage caused by:

1. Improper usage.

2. Attempts to modify or repair the flashlight by nonqualified specialists.

3. Longtime application in chlorinated or polluted water, or other liquids (other than water).

4. High temperatures and chemicals' exposure (including the exposure of liquid from defected batteries).

5. Usage of low-quality batteries.

Armytek Optoelectronics Inc.

Web: www.armytek.com Email: [email protected]

Address: 67 Vandervoort Dr, Richmond Hill, Ontario, L4E 0C7, Canada

Specifications are subject to change without notice.

Warnings

Wizard

THE MOST TECHNICALLY ADVANCED

FLASHLIGHTS IN THE WORLD

USER MANUAL

Thank you for choosing the products of Armytek Optoelectronics Inc., Canada.

Please read this manual carefully before using the flashlight.

Specifications

Armytek Optoelectronics Inc. is a Canadian manufacturer that produces powerful and reliable flashlights designed especially for your

needs applying in them components made in the USA and Japan.

Superb light of amazing constant brightness due to powerful electronics and active temperature control without timers

Multi-flashlight "10 in 1" is for many activities: car, fishing, hunting, home, work, city, picnic, bike, outdoor, travel

Efficient TIR-optics and no "tunnel vision" effect even after continuous use

Multicolor Warning Indication of low battery level and high temperature

Side switch for comfortable one-hand operation and easy modes switching with advanced operation

Multicolor State Indication and ultra low current drain in OFF-state more than 25 years

Comfortable headband for reliable fixation of the flashlight – it won't slip even while you're running

Solid body without long wires, weak rubber connectors and unnecessary boxes

Removable magnet in the tailcap, removable clip, strong lanyard and possibility of tail-stand for multipurpose use

Compact and light-weight flashlight of guaranteed durability stands up harsh impacts and falling from 10 meters

Total protection from water, dirt and dust penetration - flashlight continues to work even at the depth of 10 meters

Model

LED

Optics

Brightness stabilization type

Light output, OTF lumens*

Peak beam intensity, candelas

Hotspot/spill

Beam distance*

Hotspot diameter at 16 feet / 5 meters

Modes and runtimes (measured for Sanyo

Eneloop AA 2000 mAh / Armytek CR123A 1500

mAh / Armytek 18650 Li-Ion 3100 mAh to the

decrease to 10% of initial brightness)

Recommended power source

Length 4.25"/ 108mm, body diameter 0.96"/ 24.5mm, head diameter 1.14"/ 29mm

Size

Weight (without batteries, headband, magnet)

* Light outputs for flashlights with Warm light are about 7% less, beam distances are about 3% less.

10 years no-hassle warranty

–

Wizard Pro

Cree XM-L2

TIR

FULL stabilization (constant brightness)

1050

2900

70° / 1 20°

118 yards / 108 meters

7 meters

Firefly1: 0.2lm / 100d

Firefly2: 2lm / 18d

Firefly3: 15lm / 72h

Main1: 70lm / 18h

Main2: 200lm / 8.5h

Main3: 420lm / 3.5h

Max: 1050lm / 1.1h

Strobe: 10Hz

Warning: 0.6Hz

1x18650 Li-Ion / 2xRCR123 Li-ion / 2xCR123A

2oz / 57g